manualshive.com logo in svg

Siemens Advance Network Gateway, Руководство пользователя, Страница: 25 / 72

Поделиться
Скачать
Siemens Advance Network Gateway Скачать руководство пользователя страница 25

2000590-001

Installation  

••

  17

Wiring Connections

All input ac power and communications connections are made to con-
nectors located on the chassis power supply assembly. To gain access
to the assembly, open the front panel of the ANG_EN. For Zone 1 units
refer to the Figure 1-4, Zone 1 Outline Drawing.

Advance Data
Hiway

 

Port 1& 2

AC Power

Power
ON/OFF
Switch

ANCB (Advance
Network
Communications
Board)

Ethernet
Port

Two removable wiring access plates permit all the wiring to be made
through the bottom section (wall units) or rear section (rack units) of the
ANG_EN. The plates can be punched to accommodate conduit or cable
gland connectors. For Zone 1 units refer to the Figure 1-4, Zone 1 Out-
line Drawing.

ACCESS PLATES

AC Power (Mains) Connections Page 18
Data Hiway Cable Connections Page 20
Ethernet 10BaseT Connections Page 23

Description

Figure 2-4. Power
Supply/ANCB Assembly

I/O Wiring

Figure 2-5. Wiring
Access Plate

Instructions

Содержание Advance Network Gateway









































































Отзывы:

Нет отзывов