manualshive.com logo in svg

Siemens 6GK5 124-0BA00-3AR3, Руководство по эксплуатации

Поделиться
Скачать
Siemens 6GK5 124-0BA00-3AR3 Скачать руководство пользователя страница 37

WARNING

Devices with a 240 VAC voltage supply do not have an approval for hazardous areas

Devices with a 240 VAC power supply are not approved for use in hazardous areas according to 
ATEX, IECEx, FM and UL HazLoc.

NOTICE
Securing cables with dangerous voltage

Make sure that the connector cannot be released accidentally by pulling on the connecting 
cable. Lay the cables in cable ducts or cable channels and secure the cables, where necessary, 
with cable ties.

Note
Use in IT networks

When used in IT networks, the power supply 240 VAC also applies to the connected IT network: 
Phase-to-phase.

Information on the power supply

• The power supply is connected using an IEC plug C13/C14. The device installation plug C14 

is located on the rear panel of the device.

• The device installation plug is three pin with neutral conductor 

①

, protective conductor 

②

 

and external conductor 

③

.

• The device is grounded via the power cable.

• The power supply is single (1 x 240 VAC).

• To connect the power supply, use the power cable listed in the section "Accessories 

(Page 13)".

Position

Figure 4-2

Position of the device installation connector

Connecting up

4.5 Power supply 240 VAC

SCALANCE XR-100WG
Operating Instructions, 09/2020, C79000-G8976-C455-04

37

Содержание 6GK5 124-0BA00-3AR3































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды