manualshive.com logo in svg

Siemens 6GK5 124-0BA00-3AR3, Руководство по эксплуатации

Поделиться
Скачать
Siemens 6GK5 124-0BA00-3AR3 Скачать руководство пользователя страница 23

WARNING

EXPLOSION HAZARD

For operation the device is intended to be installed within an enclosure/control cabinet. The 
inner temperature of the enclosure/control cabinet corresponds to the ambient temperature of 
the device. Use installation wiring connections with admitted maximum operating 
temperature of at least 30 °C higher than maximum ambient temperature.

Safety notices when using the device as industrial control equipment according to UL 

61010-2-201
If you use the device under UL 61010-2-201 conditions you must also keep to the following 
safety notices in addition to the general safety notices for protection against explosion:

WARNING

Open equipment

The devices are "open equipment" according to the standard IEC 61010-2-201 or UL 
61010-2-201 / CSA C22.2 No. 61010-2-201. To fulfill requirements for safe operation with 
regard to mechanical stability, flame retardation, stability, and protection against contact, the 
following alternative types of installation are specified:
• Installation in a suitable cabinet.
• Installation in a suitable enclosure.
• Installation in a suitably equipped, enclosed control room.

WARNING

If the cable or housing socket exceeds 70 °C or the branching point of the cables exceeds 60 °C, 
special precautions must be taken. If the equipment is operated in an air ambient in excess of 
40 °C, only use cables with admitted maximum operating temperature of at least 80 ℃.

Additional notes

CAUTION

Use only approved components

If you use components and accessories that are not approved for SIMATIC NET devices or their 
target systems, this may violate the requirements and regulations for safety and 
electromagnetic compatibility.
Only use components approved for the SIMATIC NET devices.

Installation

3.1 Safety notices for installation

SCALANCE XR-100WG
Operating Instructions, 09/2020, C79000-G8976-C455-04

23

Содержание 6GK5 124-0BA00-3AR3































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды