Siemens 6ES7647-0BA00-0YA2 Скачать руководство пользователя | Manualshive

Страница: 32 / 71

background image

Expand device
5.3 Install Mini PCIe card

SIMATIC IOT2050

32

Operating Instructions, 03/2020, A5E39456816-AA

5.3

Install Mini PCIe card

You can install a Mini PCIe card in a IOT2050.

Note
Power consumption
If the power consumption of the Mini PCIe card is too high, the device will be damaged.
Note the information in section "Technical specifications (Page 48)".
Ambient temperature
The temperature in the housing of the device can be up to 30 °C above the maximum

permissible ambient temperature of the device.
Make sure that the maximum permissible ambient temperature of the Mini PCIe- card is

specified accordingly.

CAUTION

Risk of burns due to hot components
The motherboard and internal components can get hot during operation. Motherboard and

internal components will only cool down slowly after the device has been switched off.
To avoid getting burned, wait a while after switching off the power supply. Be very careful

when opening the enclosure and removing the motherboard.

5.3.1

Installing Mini PCIe card

Requirement

●

The device is disconnected from the power supply.

●

A Mini PCIe card

●

Two M2 screws (supplied in accessory kit)

Procedure

The following example describes the installation of a Mini PCIe card, including mounting of

the antenna jacks. If you install a different Mini PCIe card, the work steps 4, 5 and 7 are not

required.

«
...
30
31
32
33
34
...
»

Содержание 6ES7647-0BA00-0YA2








































































Отзывы:

Нет отзывов

Похожие инструкции для 6ES7647-0BA00-0YA2

Бренд: KAS Страницы: 2

Бренд: RTA Страницы: 73

SBO500 SBO Series

Бренд: Synway Страницы: 72

Бренд: Synway Страницы: 7

Бренд: RTA Страницы: 73

ATEUS EasyGate 501309E

Бренд: 2N Telekomunikace Страницы: 2

Dynalite DTK622-USB

Бренд: Philips Страницы: 2

Dynalite DMNG232

Бренд: Philips Страницы: 2

Dynalite DDNI-LON

Бренд: Philips Страницы: 2

Dynalite DDNG485

Бренд: Philips Страницы: 2

Dynalite DDNG232

Бренд: Philips Страницы: 2

Dynalite DDNG100BT

Бренд: Philips Страницы: 2

Dynalite DDNG-KNX

Бренд: Philips Страницы: 2

Dynalite DDMIDC8

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 80

Бренд: QNAP Страницы: 168

Бренд: Luminext Страницы: 8

Бренд: ESD Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды