Siemens 1FL3041-0AC31-0BJ0 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 60

Siemens 1FL3041-0AC31-0BJ0 Скачать руководство пользователя страница 5

I

Safety information

This manual contains safety texts which you should always observe for
your personal safety and to avoid damage. These texts are identified and
emphasized by a symbol and a heading which varies according to the
degree of danger:

!

Danger

means that death, serious injury or severe damage will result if proper
precautions are not taken.

!

Warning

means that death, serious injury or severe damage may result if proper
precautions are not taken.

!

Caution

means that minor injury or damage may result if proper precautions are
not taken.

Note

is used to give special emphasis to important information on the product,
handling the product or the relevant part of the documentation.

Qualified personnel

Start-up and operation of the unit shall only be carried out by qualified
personnel. Qualified personnel in the sense of the safety information in
this manual are those persons who are authorized for setting up, earthing
and tagging equipment, systems and circuits according to established
safety practices.

Intended use

The following should be noted:

!

Warning

This equipment may only be used for the individual applications specified
in the catalog and in this documentation and only in conjunction with
Siemens approved or recommended third-party equipment and
components.

Adequate transport, storage, installation and mounting as well as careful
use and thorough maintenance are prerequisites for safe and reliable
operation of the product.

Trademarks

SIMATIC® and SINEC® are registered trademarks of the SIEMENS AG.

«
...
3
4
5
6
7
...
»

Содержание 1FL3041-0AC31-0BJ0





























































Отзывы:

Нет отзывов