Side-Power SE IP-140 Скачать руководство пользователя страница 5

Страница: 5 / 28

4526

2020

SE IP 50

MC_0057

Technical Speciﬁ cations

Motor:

Custom made reversible DC-motor.

Gear house:

Seawater resistant bronze. Ball-bearing at propeller shaft and a combination of ball bearing and slide bearing at drive shaft.

(Pre-fi lled and sealed for life)

Motor bracket:

Glass fi bre reinforced composite material. Brass thread inserts.

Ignition

Protection:

Conforms to ISO 8846

Tunnel:

Cross spun with rowing G.R.P tunnel

Steel & aluminium tunnels available at request.

Propeller:

5-blade skewback “Q-prop” propeller, fi breglass reinforced composite.

Batteries:

Minimum recommended battery capacity (cold crank capacity by DIN/SAE standard)

Contact a battery supplier for more information.

Max. Use:

2 - 3 min. duty cycle at 20º

Safety features:

- Electronic time-lapse device protects against sudden change of drive direction.

- The electric thermal cut-oﬀ switch in electro motor protects against overheating (auto-reset when electro motor cools down).

- Flexible coupling between electro-motor and drive shaft protects electro motor and gear system if propeller jams.

- Original Sidepower panels shut oﬀ automatically 6 minutes after last use.

- Original Sidepower panels use child-safe double ON buttons.

- An integrated microprocessor monitors solenoids, reduce wear and risk of solenoid lock-in.

- Auto-stop of the thruster occurs when an undesirable solenoid lock-in occurs or when continuous operation cut-oﬀ timer exceeds

3 minutes.

MC_0136

Thruster Speciﬁ cations

description

* 50

Available DC System (v)

12v & 24v

Thrust 12v or 24v (kg * lbs)

62 kg * 136 lbs

Thrust 10.5v or 21v (kg * lbs)

40 kg * 110 lbs

Typical Boat Size (m * ft)

8m - 11m * 27ft - 37ft

Propulsion System

Single

Power (kw * Hp)

2.4kw * 3.2hp

Weight (kg * lbs)

15kg * 33lbs

*Valid for SE / SE IP & SEP / SEP IP

MG_0311

Tunnel centre line

Single Propeller

The gear leg/ propeller(s) must

never extend out of the tunnel

Propeller position will vary

with each thruster model

Содержание SE IP-140





























Результаты поиска

Содержание SE IP-140

Отзывы:

Похожие инструкции для SE IP-140

Бренды по названию

Популярные бренды

Side-Power SE IP-140, Руководство по установке

Результаты поиска

Содержание SE IP-140

Отзывы:

Похожие инструкции для SE IP-140

Бренды по названию

Популярные бренды