SICK TRANSIC Extractive TRANSIC151LP Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 84

SICK TRANSIC Extractive TRANSIC151LP Скачать руководство пользователя страница 32

32

8015383/ZUQ7/V1-3/2020-06 | SICK

O P E R A T I N G I N S T R U C T I O N S | TRANSIC151LP

Subject to change without notice

4

OPERATION

4

Operation

4.1

Safety instructions for operation

4.2

Interfaces

There are 2 control interfaces

●

Keypad (on the front TRANSIC151LP panel)

●

Maintenance interface

4.2.1

Control via keypad

A display and four pushbuttons are located on the front enclosure panel. The measured oxy-
gen value is shown on the display. LEDs signal the operating mode of the measuring device.
A green LED indicates normal operation.

Characteristics

The main purpose of the integrated interface (keypad/display) is field calibration.

The following values can be set to attain higher measurement precision:

●

Process pressure

●

Humidity

●

Carbon dioxide content

NOTE:

Risk of damage to the TSA151 through dust or humidity

▸

Only open the TSA151 in a dry environment free from dust.

NOTE:

Read the instructions through carefully before making any settings or

parameter changes. SICK accepts no responsibility for parameter or setting
changes nor adjustments made by the user. Contact SICK Customer Service
when you require technical support.

The password can be found in the Annex,

see “Password”, page 82

.

DANGER: Hazard through incorrect parameter settings

Incorrect settings for parameters can have severe consequences. This is why the
password may only be available for authorized technicians.

▸

Note the password in the Manual and keep it safe somewhere else,

see “Password”,

Changes to parameters are password protected. The password allows access for
30 minutes after entry.

«
...
30
31
32
33
34
...
»

Содержание TRANSIC Extractive TRANSIC151LP





















































































Отзывы:

Нет отзывов