manualshive.com logo in svg

SICK TRANSIC Extractive TRANSIC151LP, Руководство по эксплуатации, Страница: 24 / 84

Поделиться
Скачать
SICK TRANSIC Extractive TRANSIC151LP Скачать руководство пользователя страница 24

24

8015383/ZUQ7/V1-3/2020-06 | SICK

O P E R A T I N G   I N S T R U C T I O N S  |  TRANSIC151LP

Subject to change without notice

3

INSTALLATION 

 Installing the sample gas line

1

Provide adequate support for the tubing, for example by attaching it to the wall. 
The tube must not put any traction on the connection. 

2

The sample gas cell has two gas connections. Use the gas connection closest to the 
TRANSIC151LP as gas inlet. This provides a better gas exchange and shorter response 
times.

Installing the sample gas cell

Dimensions of the TRANSIC151LP with sample gas cell, 

see “TRANSIC151LP with wall 

bracket and sample gas cell (suitable for PS=10 bar(g))”, page 71

.

When a TRANSIC151LP with sample gas cell is ordered, it is delivered with the cell fixed at 
the factory and prepared for wall fitting. 

▸

Take the sample gas cell off to check and replace the filter.

1

 Loosen the bayonet tube screw fitting, 

see “Removing the sample gas cell”, page 24

, 

turn the sample gas cell and then pull it off the TRANSIC151LP, 

see “Removing the 

sample gas cell”, page 24

.

2

Refit the bayonet screw fitting in the reverse sequence. 
Ensure the seal is located between the sample gas cell and measuring device 
enclosure. The Swagelok connections must point directly downwards.

Fig. 8: Removing the sample gas cell

Содержание TRANSIC Extractive TRANSIC151LP





















































































Отзывы:

Нет отзывов