SICK CLV 210 Скачать руководство пользователя страница 6

Страница: 6 / 12

Quick-Start
CLV 210...CLV 212 Bar Code Scanners

SICK AG

Division Auto Ident

Germany

8 007 825/01-2002

8. Setup

‡ Switch on the power supply 24 V DC for the CLV

The device switches to

Reading mode automatically after the initialization procedure and self-test. The device

name and software version are displayed on the screen. The device then waits for a signal from the external
sensor to start the reading function.

You must switch to

Percentage Evaluation mode to read a bar code without a sensor connected.

‡ Press the [ ESC ] key twice; select and confirm the "Percentage evaluation" menu item in the main menu.
‡ Hold the printed code sample in front of the reading window at a distance of approx. 120 mm (CLV 210,

CLV 211) or 70 mm (CLV 212). The scan line should cross the code bars at a right angle (

Fig. 7).

The device then evaluates 100 readings continuously and outputs the result on the screen as shown in

Fig. 8.

Fig. 8. Example: read results on the screen for a successful read

Fig. 7. Scan line/code assignment

Line scanner

Raster scanner

where:

T T=

Duration of read interval

MG=

Mean time value of identification quality

Number of codes detected

C39=

Code type code 39

100%=

Identification quality

ST=

Read status (0= Good read)

CP=

Code position

CL=

Code length

CA=

Required scans

CS=

Code reliability

CK=

Code continuity

UVWXYZ=

Code content

T T= _ _160 ms MG=_10% n=_1

C39 100% ST=0 CP=_46 CL=12 CA=_ _3 CS=109 CK=_ _1

UVWXYZ

Successful reading (Good read):

module width 0.35 mm

Code sample (Code 39):

Содержание CLV 210













Результаты поиска

Содержание CLV 210

Отзывы:

Похожие инструкции для CLV 210

Бренды по названию

Популярные бренды

SICK CLV 210, Быстрый старт

Результаты поиска

Содержание CLV 210

Отзывы:

Похожие инструкции для CLV 210

Бренды по названию

Популярные бренды