background image

- 68 -

#

#

#

#

#

Advanced Chipset Features

This section allows you to configure the system based on the specific
features of the installed chipset.  This chipset manages bus speeds and

access to system memory resources, such as DRAM and the external
cache.  It also coordinates communications between the conventional
ISA bus and the PCI bus.  It states that these items should never need to
be altered.
The default settings have been chosen because they provide the best
operating conditions for your system.  If you discovered that data was
being lost while using your system, you might consider making any
changes.

DRAM Clock/Drive Control

Options are in its sub-menu.
Press <Enter> to enter the sub-menu of detailed options.

Current FSB Frequence

This item show Current CPU Front Side Bus speed.

Current DRAM Frequence

This item show Current DRAM speed.

DRAM Clock

This item allows you to control the DRAM speed.

"

The Choice: 100MHz, 133MHz, or By SPD.
When CPU speed set to 100MHz, DRAM speed can be set to
100MHz( by Host Clock) , or 133MHz (by Host Clock+33MHz).

Содержание Spacewalker AK32


























































































Отзывы: