background image

Page 12

Shuttle Brewers & Airpot/Shuttle Brewers

Programming (cont.)

Settings Routine

Programming For 

Small

: Brew Time & Pulse Brewing (refer to Table 3)

1

1. Press and hold both “up” and “down” arrows for 5 seconds.

1

2. All three “brew” lights will flash.

1

3. Press “Small Brew” button.

Only “Small” ready light illuminates during remaining steps.

1

4. Display will read “Br” (Brew Time).

1

5. Press “Small Brew” button to go to next setting.

1

6. Display will read set brew time in minutes and seconds (0.01-6.00). Default is “1.20”.

1

7. Press “up” or “down” arrow to change value (1 second increments). (Approximately 0.8 oz./second.)

1

8. Press “Small Brew” button to accept and go to next setting.

1

9. Display will read “P-b” (Pulse Brewing).

10. Press “Small Brew” button to accept and go to next setting.
11. Display will read “Off” or “1” – “6” (number of pulses). Default is 4.
12. Press “up” or “down” arrow to change value. (increments of 1)
13. Press “Small Brew” button to accept and go to next setting.

Note: If “Off” is selected, skip pulse timing steps.

14. Display will read “0.05” – “0.60” (pulse ON time for each pulse). Default is “0.20”.
15. Press “up” or “down” arrow to change value. (increments of 1 second)
16. Press “Small Brew” button to accept and go to next setting.
17. Display will read “0.05” – “0.60” (pulse OFF time for each pulse). Default is “0.20”.
18. Press “up” or “down” arrow to change value. (increments of 1 second)
19. Press “Small Brew” button to accept and clear display.

* During programming routine, all other brew buttons are disabled.

r brew buttons are disabled.

* If ON/OFF button is pressed during programming routine, brew defaults to previous settings.

Table 3

3. PRESS BREW BUTTON FOR SMALL "S".

READING

2. READY LIGHTS WILL FLASH.

S

S

S

5. DISPLAY WILL READ AS FOLLOWS:

PULSE OFF TIME (0:05-0:60)

PULSE ON TIME (0:05-0:60)

PULSE BREW

(OFF, 1 - 6)

# OF PULSES

TO

DISPLAY

BREW TIME (0:01-6:00)

BREW TIME

ADVANCE

ADJUST

4. SMALL READY LIGHT FLASHES THROUGHOUT ROUTINE.

S

1. PRESS-AND-HOLD UP & DOWN ARROWS FOR 5 SECONDS.

S

S

Содержание PB-330





































Отзывы: