Shuttle HOT-559 Скачать руководство пользователя | Manualshive

Страница: 9 / 33

background image

User's Manual 9

1.8 Main Board Connectors

There are connectors on-board for Power supply, Floppy, IDE, back panel connector,
and front panel I/O.

Front panel Connector

The HOT-559(S) main board provides header connectors to support function
typically located on the chassis bezel. Front panel features support include :

*

Infra-red (IrDA) Port

*

System Reset

*

EPMI

*

Green LED

*

System Speaker

*

Power LED & KeyLock

*

IDE Hard Drive active LED

*

Sleep & Power Control Port

*

SCSI Hard Drive active LED

Speaker

The external speaker provides error beep code information during the Power-on Self
Test, if the system cannot use the video interface.

Sleep / Resume

When Advanced Power Management (APM) is activated in the system BIOS and the
Operating System's APM driver is loaded, Sleep mode (Standby) can be entered in
one of three ways: an optional front panel "Sleep/Resume" button, a user defined
keyboard hot key, or prolonged system inactivity. The Sleep/Resume button is
supported by a 2-pin header located on the front panel I/O connector. Closing the
"Sleep" switch will generate an SMI (System Management Interrupt) to the processor
which immediately goes into System Management Mode (SMM), the so called
"Sleep" mode.

The front panel "Sleep mode" switch must be a momentary two pin SPST type that is
normally open. The function of the Sleep/Resume button can also be achieved via a
keyboard hot-key sequence, or by a time-out of the system inactivity timer. Both the
keyboard hot-key and inactivity timer are programmable in the BIOS setup. To
reactivate the system, or "Resume", the user must simply press the sleep/resume
button again, or use the keyboard or mouse. Mouse activity will only "wake up" the
system is a mouse driver is loaded. While the system is in Stand-by or "sleep" mode
it is fully capable of responding to and servicing external interrupts (such as incoming
FAX) even though the monitor will only turn on if a user interrupt (keyboard/mouse)
occurs as mentioned above.

«
...
7
8
9
10
11
...
»

Содержание HOT-559


































Отзывы:

Нет отзывов

Похожие инструкции для HOT-559

Бренд: ASRock Industrial Страницы: 44

Бренд: Gigabyte Страницы: 40

Бренд: Xilinx Страницы: 40

Бренд: ST Страницы: 11

Бренд: TYAN Страницы: 64

PP-I7RS400 PURE PERFORMANCE II

Бренд: Sapphire Audio Страницы: 44

Бренд: Xilinx Страницы: 88

Бренд: IBASE Technology Страницы: 81

Бренд: Gigabyte Страницы: 81

Бренд: AOpen Страницы: 8

Бренд: Embedian Страницы: 70

Бренд: Gigabyte Страницы: 96

Бренд: Supermicro Страницы: 84

Бренд: Texas Instruments Страницы: 7

Бренд: MAX power Страницы: 20

Бренд: ASROCK Страницы: 113

Бренд: Supero Страницы: 121

Бренд: ASROCK Rack Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды