Shuttle AE25 Скачать руководство пользователя | Manualshive

Страница: 65 / 79

background image

- 63 -

USB Controller

Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have USB peripherals.

"

The choice: Enabled or Disabled.

USB Keyboard Support

Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.

"

The choice: Enabled or Disabled.

Init Display First

This item allows you to decide to activate whether PCI Slot or AGP Slot
first.

"

The choice: PCI Slot or AGP .

Onboard Audio Chip

This item allows you to decide to enable/disable the hardware audio
chipset to support Audio.

"

The choice: Enabled or Disabled.

IDE HDD Block Mode

Block mode is also called block transfer, multiple commands, or mul-
tiple sector read/write. If your IDE hard drive supports block mode
(most new drives do), select Enabled for automatic detection of the
optimal number of block read/writes per sector the drive can support.

"

The choice: Enabled, or Disabled

POWER ON Function

This item is used to defined Keyboard & PS/2 mouse power-on function
enabled or disabled.

"

The choice: Hot-KEY, Mouse Move, Mouse Click, Any KEY,
Button Only, Keyboard 98.

Note USB Keyboard, USB Mouse and Serial Mouse are not

supported to this function.

Hot Key Power ON

Power-on by soft-on/off button and keyboard are available.

"

The choice: <Ctrl><F1> to <Ctrl><F12>.

«
...
63
64
65
66
67
...
»

Содержание AE25
















































































Отзывы:

Нет отзывов

Похожие инструкции для AE25

DCDC SBC Series

Бренд: Infineon Страницы: 17

Бренд: Texas Instruments Страницы: 8

Бренд: IBM Страницы: 40

Бренд: AOpen Страницы: 8

Бренд: ASROCK Страницы: 80

Бренд: ON Semiconductor Страницы: 5

Бренд: IEI Technology Страницы: 147

Бренд: Quick Страницы: 24

Бренд: Texas Instruments Страницы: 16

Бренд: Gigabyte Страницы: 84

Бренд: NXP Semiconductors Страницы: 12

Бренд: Gigabyte Страницы: 76

Бренд: Newport Страницы: 30

Z68A-G45 B3 Series

Бренд: MSI Страницы: 138

Бренд: OLIMEX Страницы: 17

Бренд: Alinx Страницы: 29

STEVAL-IHM022V1

Бренд: ST Страницы: 58

Бренд: TYAN Страницы: 117

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды