Shuttle AE25 Скачать руководство пользователя | Manualshive

Страница: 66 / 79

background image

- 64 -

Onboard FDC Controller

This item specifices onboard floppy disk drive controller. This setting
allows you to connect your floppy disk drives to the onboard floppy
connector. Choose the "Disabled" settings if you have a separate
control card.

"

The choice: Enabled Disabled.

Onboard Serial Port1/Port2

Select an address and corresponding interrupt for the first and second
serial ports.

"

The choice: 3E8/IRQ4, 2E8/IRQ3, 3F8/IRQ4, 2F8/IRQ3,Auto, or
Disabled.

UART Mode Select

The main board support IrDA infrared through COM 2 port.
Note : FIR is not available currently.

"

The choice: IrDA, ASKIR, or Normal.

UR2 Duplex Mode

This item specifies onboard infrared transfer mode to full-duplex. This
item will not show up when IrDA, ASKIR modes are selected.

"

The choice:

Full, Half.

Onboard Parallel Port

This item allows you to determine onboard parallel port controller I/O
address setting.

"

The choice:: 378/IRQ7, 278/IRQ5, 3BC/IRQ7, or Disabled.

Parallel Port Mode

Select an operating mode for the onboard parallel (printer) port. Select
Normal, Compatible, or SPP unless you are certain your hardware and
software both support one of the other available modes.

"

The choice: SPP, EPP, ECP, or ECP/EPP.

ECP Mode Use DMA

Select a DMA channel for the parallel port for use during ECP mode.

"

The choice: 1 or 3.

«
...
64
65
66
67
68
...
»

Содержание AE25
















































































Отзывы:

Нет отзывов

Похожие инструкции для AE25

Бренд: ON Semiconductor Страницы: 5

Бренд: Supermicro Страницы: 256

Бренд: DFI Страницы: 115

i.MX 8M Mini SODIMM SOM

Бренд: iWave Страницы: 16

Бренд: Advantech Страницы: 88

Бренд: ASROCK Страницы: 40

Бренд: WinSystems Страницы: 16

Бренд: TRIGEM Страницы: 17

Бренд: JETWAY Страницы: 54

Бренд: Abit Страницы: 134

Бренд: Lenovo Страницы: 51

Бренд: Acorp Страницы: 27

Бренд: Advantech Страницы: 5

Бренд: Advantech Страницы: 4

Бренд: Advantech Страницы: 122

mATX i915GV2-IGM Series

Бренд: Advantech Страницы: 54

Бренд: Asus Страницы: 22

Бренд: Asus Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды