background image

8

One Shogun DJ RG-100 (Stand-alone)

There are 4 possibilities: 

Stand Alone
Sound-active mode (Master)
Auto Mode (Master)
DMX

1. 

Fasten the Shogun onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.

2. 

Plug the cord into a proper electric power supply socket.

FUNCTION

DMX DIPSWITCH CHART

1

2

3

4

5

6

7

8

9

10

11

12

Sound Active

---

---

---

---

---

---

---

---

---

---

---

---

Auto Mode

---

---

---

---

---

---

---

---

---

---

---

ON

Master Sound

---

---

---

---

---

---

---

---

---

---

ON

---

Master Auto

---

---

---

---

---

---

---

---

---

---

ON

ON

Slave

---

---

---

---

---

---

---

---

---

ON

---

---

DMX Mode

Set DMX ADDRESS

ON

---

ON

Test Mode

---

---

---

---

---

---

---

---

---

ON

ON

---

Sound-Active

Turn on the music. If Dip switches are all set to 0, then the fixture will react to the beat of the music.

See page 10 for Dipswitch settings. After every new dipswitch setting you have to disconnect the power,
and then turn the power on to activate the new dipswitch setting. You can use the Audio sensitivity knob on
the back of the Shogun, to adjust the sensitivity reaction to the music.

Auto Mode

If Dip switches are set to 1000000000, then the fixture will play all pre-programmed patterns.

Multiple Shoguns DJ RG-100 (Master-Slave)

1. 

Fasten the effect light onto firm trussing (Use a 30-kg rated or stronger C-clamp fastened onto the

    Shogun ). Leave at least 1 meter on all sides for air circulation.

2. 

Use a 3-p XLR cable to connect the Shoguns and other devices.

    The pins:

1.

Earth

2.

Signal -

3.

3.

 Link the units as shown in (figure 4), Connect a DMX signal cable from the first unit's DMX "out" socket to

    the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.

4. 

Set DMX dip switches as follows (See Dip Switch setting page 10).

Shogun DJ RG-100

DMX Dip Switches "ON"

Unit 1 (Master)

Either Sound Active (All dipswitches OFF)
or Auto Mode Dipswitch #12 ON

Unit 2 (Slave)

Dipswitch #10 ON

Unit 3 (Slave)

Dipswitch #10 ON

Unit 4 (Slave)

Dipswitch #10 ON

5.

 

Supply electric power: Plug the end of the mains power cord into proper electric power supply sockets.

Содержание Shogun DJ RG-100


















Отзывы: