background image

 

 

 

6 

 

  

 

 

Illumisphere 50 

Product code: 41123 

2.

 

Safety 

 

Important 
Read and follow the instructions in this user manual before installing, operating or 
servicing this product. 

The manufacturer will not accept liability for any resulting damages caused by the non-observance of 
this manual. 

 

Warnings and Safety Instructions 

 

DANGER 
Danger for children
 

For adult use only. The device must be installed beyond the reach of children. 

 

Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within 
children’s reach. Packaging material is a potential source of danger for children. 

 

DANGER 
Electric shock caused by dangerous voltage inside
 

There are areas within the device where dangerous touch voltage (> 120 V DC) may be present. 

 

Do not open the device or remove the sphere. 

 

Do not operate the device if the sphere is not attached. Before operation, check if the sphere is 
firmly attached and all screws are tightly fastened. 

 

Disconnect the device from electrical power supply before service and maintenance, and when the 
device is not in use. 

 

DANGER 
Electric shock caused by short-circuit
 

This device falls under IEC protection class I. 

 

Make sure that the device is electrically connected to ground (earth). Connect the device only to a 
socket outlet with ground (earth) connection. 

 

Do not cover the ground (earth) connection. 

 

Do not bypass the thermostatic switch or fuses. 

 

Do not let the power cable come into contact with other cables. Handle the power cable and all 
connections with the mains with caution. 

 

Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable. 

 

Make sure that the power cable is not crimped or damaged. Examine the power cable periodically 
for any defects. 

 

Do not immerse the device in water or other liquids. Do not install the device in a location where 
flooding may occur. 

 

Do not use the device during thunderstorms. Disconnect the device from the electrical power supply 
immediately. 

 

 

Содержание Illumisphere 50





























Отзывы: