background image

 

 

 

5 

 

  

 

 

Illumisphere 50 

Product code: 41123 

 

Text Conventions 

Throughout the user manual the following text conventions are used: 

 

Buttons:    

All buttons are in bold lettering, for example “Press the UP/DOWN buttons” 

 

References: 

References to chapters are in bold lettering, for example: “Refer to 2. Safety” 

 

0–255: 

 

Defines a range of values 

 

Notes: 

 

Note: (in bold lettering) is followed by useful information or tips 

 

Symbols and Signal Words 

Safety notes and warnings are indicated throughout the user manual by safety signs. 

Always follow the instructions provided in this user manual. 

 

DANGER 

Indicates an imminently hazardous situation which, if not avoided, will result in 
death or serious injury. 

 

WARNING 

Indicates a potentially hazardous situation which, if not avoided, could result in 
death or serious injury. 

 

CAUTION 

Indicates a potentially hazardous situation, which, if not avoided, may result in 
minor or moderate injury. 

 

Attention 

Indicates important information for the correct operation and use of the 
product. 

 

Important  Read and observe the instructions in this document. 

 

Electrical hazard 

 

Hot surface 

 

Provides important information about the disposal of this product. 

 

Symbols on the Information Label 

This product is provided with an information label. The information label is located on the non-
detachable power cable. 

The information label contains the following symbols: 

 

This device is designed for indoor use. 

 

This device falls under IEC protection class I. 

 

This device shall not be treated as household waste. 

 

 

Содержание Illumisphere 50





























Отзывы: