SHOWTEC Explorer 575 Wash MKII, Руководство пользователя

Страница: 5 / 27

3
 Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution!
 Never remove warning or informative labels from the unit.
 Never use anything to cover the ground contact.
 Never run the device without lamp!
 Never ignite the lamp if the objective-lens or any housing-cover is open, as discharge lamps may expose
and emit a high ultraviolet radiation, which may cause burns.
 Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold
the fixture at the transport handles.
 Never place any material over the lens.
 Never look directly into the light source.
 Never leave any cables lying around.
 Do not insert objects into air vents.
 Do not connect this device to a dimmerpack.
 Do not switch the device on and off in short intervals, as this would reduce the lamp’s life.
 Do not touch the device’s housing bare-handed during its operation (housing becomes very hot). Allow the
fixture to cool for at least 5 minutes before handling.
 Do not shake the device. Avoid brute force when installing or operating the device.
 Only use device indoor, avoid contact with water or other liquids.
 Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly
fastened.
 Only operate the device after having familiarized with its functions.
 Avoid flames and do not put close to flammable liquids or gases.
 Always replace the lamp, when it is damaged or deformed due to the heat.
 Always keep case closed while operating.
 Always allow free air space of at least 50 cm around the unit for ventilation.
 Always disconnect power from the mains, when device is not used, before cleaning or when replacing
lamp! Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
 To ensure the longest and most efficient use of the lamp always wait 15 minutes before re-applying power
after a shutdown. Failure to do so could result in premature aging of the lamp and failure to the electronics
that drive it.
 Make sure that the device is not exposed to extreme heat, moisture or dust.
 Make sure that the available voltage is not higher than stated on the rear panel.
 Make sure that the power-cord is never crimped or damaged. Check the device and the power-cord from
time to time.
 If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due to cracks
or deep scratches.
 If device is dropped or struck, disconnect mains power supply immediately. Have a qualified engineer
inspect for safety before operating.
 If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it
on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.
 If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely (preferably
in the original packing material), and return it to your Showtec dealer for service.
 For adult use only. Movinghead must be installed out of the reach of children. Never leave the unit running
unattended.
 Never attempt to bypass the thermostatic switch or fuses.
 For replacement use lamps and fuses of same type and rating only.
 The user is responsible for correct positioning and operating of the Explorer. The manufacturer will not accept
liability for damages caused by the misuse or incorrect installation of this device.
 Replace the lamp if it becomes defective or worn out, or before usage exceeds the maximum service life.
 Allow the fixture to cool down for 15 minutes, before opening the fixture and replacing lamp. Protect your
hands and eyes with gloves and safety glasses.
 This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to
earth.
 During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
 Repairs, servicing and electric connection must be carried out by a qualified technician.
 WARRANTY: Till one year after date of purchase.
CAUTION ! EYEDAMAGES !.
Avoid looking directly into the light source.
(meant especially for epileptics) !