SHOWTEC Creator 1024 pro Скачать руководство пользователя страница 42

Страница: 42 / 44

Ordercode: 50731

Creator 1024 PRO

No Response to DMX

Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.

01)

Check the DMX setting. Make sure that DMX addresses are correct.

02)

Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical
power. Try your DMX control again.

03)

Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products ? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.

Playback Buttons Do Not Respond to Commands

Please check MIDI status in Setup menu. MIDI Slave mode will disable the playback buttons and the
device will respond only to MIDI master commands.

Product Specifications

DMX channel

1024

Fixture

Re-patched fixture address

Yes

Swop Pan/Tilt

Yes

Reversed channel output

Yes

Channel slope modification

Yes

Channels for each fixture

40 p 40 fine tune

Library

Avolite Pearl R20 library supported

Scene

600

Scenes to run simultaneously

Total scene steps

600

Time control of scenes

Fade IN/OUT, LTP slope

Shapes for each scene

Scene and dimmer by slider

Yes

Swop scene

Yes

Flash scene

Yes

Shape generator

Shapes of Dimmer, Pan/Tilt, RGB, CMY,
Color, Gobo, Iris and Focus

Shapes to run simultaneously

Master slider

Global, playback, fixture

Real time blackout

Yes

Channel value by wheel

Yes

Channel value by slider

Yes

Dimmer by slider

Yes

USB memory

FAT32 supported

Fuse:

F1L/250V

Dimensions:

655 x 550 x 135 mm (LxWxH)

Weight:

12,6 kg

Design and product specifications are subject to change without prior notice.

Website:

www.Showtec.info

Email:

[email protected]

Содержание Creator 1024 pro













































Результаты поиска

Содержание Creator 1024 pro

Отзывы:

Похожие инструкции для Creator 1024 pro

Бренды по названию

Популярные бренды

SHOWTEC Creator 1024 pro, Руководство пользователя

Результаты поиска

Содержание Creator 1024 pro

Отзывы:

Похожие инструкции для Creator 1024 pro

Бренды по названию

Популярные бренды