background image

E N  

 

 

Nome file:

File name:

7528002EN - ISTRUZIONI WP7.8000 - EN.docx 

Rev. 1 24/05/2016 

15-18 

 

P

ROBLEM

 

C

AUSE

 

1

ST

 

S

OLUTION

 

2

ND

 

S

OLUTION

 

9.  Low flowrate from 

outlet 

The impeller’s blades are 
worn out. 

Replace the impeller. 

Contact specialised 
technicians. 

10. Low flowrate from 

outlet 

The  pump  has  not  been 
primed correctly. 

Prime the pump

Contact specialised 
technicians. 

11. The product does not 

work. 

The thermal protector 
has been triggered. 

Check that the water 
temperature does not 
35 [°C] and, if 
necessary, add cold 
water to the pool to lower 
water temperature. 

Contact specialised 
technicians. 

12. The product does not 

work. 

The thermal protector 
has been triggered. 

Blocked drive shaft, 
follow the instructions in 
Blocked rotor. 

Contact specialised 
technicians. 

13. Water leak. 

Gaskets or o-rings 
incorrectly installed 

Check correct gasket 
and o-ring installation. 

Contact specialised 
technicians. 

14. Water leak. 

Fast connections or 
cover not tight. 

Tighten fast connections 
and cover. 

Contact specialised 
technicians. 

15. Loss of water from 

mechanical seal

mechanical seal is 
used to isolate the pump 
body and the motor 
body. Some drops of 
water may flow out once 
in a while this is normal, 
especially after periods 
of non use. 

If the leaks are 
consistent Please 
contact specialised 
technicians.. 

16. Blocked rotor. 

Foreign bodies block the 
rotating elements of the 
product (impeller or 
cooling fan). 

Remove any foreign 
bodies. 

Contact specialised 
technicians. 

17. Blocked rotor. 

Blocked drive shaft, it 
can happen after a long 
period of inactivity. 

Do the following: 

1.  unplug the 

product from the 
power outlet

2.  make the drive 

shaft turn 9-10 
times, using a 
screwdriver as 
shown in Fig. ; 

3.  insert the power 

plug of the 
product into the 
power outlet. 

Contact specialised 
technicians. 

Tab. 2 

 

Fig. 29 

 

Содержание WP7000



















Отзывы: