Shott WP7000 Скачать руководство пользователя страница 13

E N  

 

 

Nome file:

File name:

7528002EN - ISTRUZIONI WP7.8000 - EN.docx 

Rev. 1 24/05/2016 

13-18 

 

6.4  Operating limits and environmental limits. 

 

Maximum water temperature: +35 [°C]. 

 

Minimum water temperature: +4 [°C]. 

6.5  Safety devices and signalling. 

  The product is equipped with a thermal protector. Following any thermal 

protector  operation,  check  the  causes  that  originated  the  product’s 
malfunction.  For  this  purpose,  please  consult  the  “Troubleshooting” 
section. 
The  product  shall  go  back  to  normal  operating  conditions  after  it  has 
cooled  down  (about  2÷3  hours)  and/or  the  caused  that  triggered  the 
thermal protector have been eliminated. 
6.6  Hazards and risks. 

  Attention  to  the  inlet/outlet  points  because  they  can  trap  parts  of  the 

body and/or hair and cause serious personal injuries and even death. 

  Pumps,  filters,  and  other  equipment/components  of  a  pool  filtration 

system  can  operate  under  pressure.  If  not  correctly  installed  they  can 
cause serious personal injuries and even death. 
The  product  is  powered  electrically,  so  maximum  diligence  in  its 
installation and maintenance is required, in order to avoid danger. Please 
pay particular attention to: 

 

the conditions of its power cord, which must not be damaged; 

 

do  not  use  the  product  without  its  pre-filter  basket  (Fig.  ?,  #  ?), 

otherwise the product may jam or be irreparably damaged; 

 

when  using  any  type  of  stop  valve  make  sure  the  line  is  completely 

open as the product must never run with valves closed. 

 

7.1  Description of the control/command devices. 

  Power plug with residual current device (RCD, when included). 

  Before turning on the product, always press the RESET button. Check 

power  plug  with  residual  current  device  operations  by  pressing  the TEST 
button (T). 

  Do  not  attempt  to  repair  or  open  the  power  plug  with  residual  current 

device;  in  the  event  of  fault,  replace  the  entire  power  plug  with  residual 
current device
 with the power cord
The  power  plug  with  residual  current  device  does  not  replace  mandatory 
electrical  safety  components:  the  electrical  system  must  meet  current 
international and/or national regulations. If necessary, contact specialised 
technicians. 

  The power plug with residual current device is an additional electrical safety component able to cut off a 

circuit in the event of fault. In order for it to work, it must: 

 

always be in the vertical position, 

 

always be clean and free of dust or water, 

 

be connected to a perfectly efficient ground line, 

 

check residual current device operations before turning on the product. 

  Checking residual current device operations. 

Plug the power plug with residual current device into the power outlet: 
1.  press  the  RESET  button  to  allow  the  product  to  be  turned  on:  the  light 
turns red. 
2.  press  the  TEST  (T)  button  to  test  residual  current  device  operations:  the 
light  turns  off  and  the  residual  current  device  cuts  off  electrical  power, 
therefore  the  product  cannot  be  turned  on  unless  the  RESET  button  is 
pressed again. 

  If the residual current device triggers (turns off the product) during product 

use, unplug the power plug with residual current device from the power outlet 

 

Fig. 24 

 

Fig. 25 

 

Fig. 26 

Pa

 

Fig. 27 

TEST (T)

RESET

Содержание WP7000



















Отзывы: