ShopBot PRS Скачать руководство пользователя страница 50

Страница: 50 / 54

pg.

As the cables exit the chain, keep the spindle/router

cord separate while bundling the other cables into

one or two “cable ropes.”

Make sure to include the X2 motor cable that you

routed through the gantry beam, as well as the X1

motor and the X axis proximity switch (located on

this side of the gantry).

Secure this bundle to one of the holes in the side of

the end plate using a wire tie.

Cable management without an E-chain

Note:

This step only applies to tools with a 48” or 60” X axis.

Skip to the next section if you are working with a 96” table or

longer.

If you are setting up a tool with an X axis of 60” or shorter, or if you

had purchased this tool before 2013, an X axis E-chain is not included.

Continue to bundle the cable rope by adding wire ties every 12-16”.

Move the gantry along its full extent of travel to determine how much

slack is needed in the cable rope. Then secure it to the underside of

the table (using any unused holes in the cross-supports) until you

reach the other table side where the control box will be installed.

Any leftover cable should be made into large loops and secured under

the table. Avoid making tight coils, which can act as an antenna for

electrical interference.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

Содержание PRS























































Результаты поиска

Содержание PRS

Отзывы:

Похожие инструкции для PRS

Бренды по названию

Популярные бренды

ShopBot PRS, Инструкция по сборке

Результаты поиска

Содержание PRS

Отзывы:

Похожие инструкции для PRS

Бренды по названию

Популярные бренды