ShopBot PRS Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 54

background image

pg.

37

Mounting a 10” VFD

Use a 1/4-20x3/4” button head screw, washer, and

nylock nut to attach the upper left corner of the

VFD to the left-most hole on the mounting strap.

Repeat on the lower left corner of the VFD with

the other mounting strap.

Locate the three pairs of holes on the center leg of the

front side

of your table. The 10” VFD will attach

to the

upper and middle pairs.

Starting with the upper pair of holes, thread another

button head screw into the upper right corner of the

VFD, through the mounting strap and the table leg.

Secure using washer and nut. Repeat with lower

right corner of the VFD.

Use the remaining 1/4-20x5/8” flat head screw,

washer and nut to secure the far right side of

the strap to the table leg. Repeat with the lower

strap.

This completes the mounting procedure for

the 10” VFD. Skip to the next section,

“Connecting power to your Spindle”.

Assemble Your Shopbot PRS Gantry Tool 2015 02 27.Docx

© 2015 ShopBot Tools, Inc.

«
...
35
36
37
38
39
...
»

Содержание PRS























































Отзывы:

Нет отзывов

Похожие инструкции для PRS

Бренд: ABB Страницы: 18

Бренд: R-Tech Страницы: 3

Бренд: KaVo Страницы: 16

Бренд: GE Страницы: 24

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Бренд: RASHA PROFESSIONAL Страницы: 11

Бренд: MADRIX Страницы: 24

Бренд: MADRIX Страницы: 28

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: Tanco Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды