background image

EMPTYING LIQUID WASTE FROM THE TANK

Use special care when emptying heavily loaded tanks. Your Wet/Dry Vacuum may be emptied of waste by removing the tank cover. To empty, stop 

the motor and remove the plug from the wall receptacle. Remove the tank cover and deposit the liquid waste contents into a suitable drain. Your 

Wet/Dry Vac also comes with a convenient tank drain. Simply remove the drain cap and empty the liquid contents into a suitable drain. After the 

tank is empty, return the cover to its original position. To continue use, plug the cord into the wall receptacle and start the motor.

WET PICK UP OPERATION

When vacuuming fine dust or powders of any kind - (eg) plaster, drywall 
dust, cold ashes, concrete dust, etc. . . a disposable collector filter bag
must be used. These "large bag" filters connect to the air inlet fitting on the 
inside of the vacuum tank. 
1.  Grasp cardboard collar firmly and slide rubber guard onto inlet fitting as 

far as possible.

2.  When secured in place, expand bag and position around side of tank.

USE FOR DRY PICK UP ONLY

CORRECT DISPOSABLE FILTER INSTALLATION

WARNING - 

ALWAYS WEAR EYE PROTECTION TO PREVENT ROCKS OR DEBRIS FROM BEING 

BLOWN OR RICOCHETING INTO THE EYES OR FACE WHICH CAN RESULT IN SERIOUS INJURY.

BLOWER FEATURE

This vacuum can be used as a powerful blower. To use your unit as a blower insert hose end into blower port on 
rear of unit. Clear hose of any obstructions before attaching to blower port. Caution should be used when using as 
a blower due to the powerful force of air when using certain attachments.

Remove ALL dirt and debris found in the tank. The vacuum requires only a minimum of conversion when going from dry to wet pick up. Wet pick 

up requires the foam sleeve 

(not standard on all models) 

to be in position over the lid cage. Do not use the reusable dry filter 

(not standard on 

all models) 

for wet pick up. Misting in exhaust air may occur if the foam sleeve becomes saturated during wet pick up. If misting occurs, remove 

and dry the saturated foam sleeve or replace with another dry foam sleeve to eliminate the misting and possible dripping of liquid around the lid. 

Turn the unit off immediately upon completing a wet pick up job or when tank is full and ready to be emptied. Raise the hose to drain any excess 

liquid into the tank. The interior of the tank should be periodically cleaned.
The foam sleeve should be cleaned periodically as described in the following steps:

1.  Always disconnect the plug from the wall receptacle before removing the tank cover. Place tank cover in an upside down position. Remove 

     foam sleeve by sliding it up and off the lid cage.

2.  Shake excess dust off foam sleeve with a rapid up and down movement.

3.  Hold foam sleeve under running water for a minute or two, rinsing from the inside. A water wash is not always required, depending on the 

     condition of the foam sleeve.

4.  Gently wring out excess water, blot foam sleeve with a clean towel, and allow to dry. The foam sleeve is now ready to be reinstalled on the lid 

     cage.

NOTE: WET PICK UP ACCESSORIES SHOULD BE WASHED PERIODICALLY, ESPECIALLY AFTER PICKING UP WET, STICKY KITCHEN ACCIDENTS. THIS 

CAN BE ACCOMPLISHED WITH A WARM SOLUTION OF SOAP AND WATER.

INSTALLING THE CARTRIDGE FILTER •

   

NOT STANDARD ON ALL MODELS

  

WARNING - 

ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET BEFORE REMOVING 

THE TANK COVER.

1.  Slide cartridge filter down over lid cage.
2.  Place filter retainer on top of cartridge filter. Hold onto base of lid 
 

cage with one hand and turn retainer clockwise to tighten.

3.  To remove filter for cleaning, again hold onto base of lid cage with 
 

one hand and turn retainer counter clockwise to loosen.

4.  Slide cartridge filter off lid cage.

TIGHTEN

LOOSEN

INSTALLING THE DISPOSABLE FILTER BAG 

   

NOT STANDARD ON ALL MODELS

Отзывы: