Trouble
Possible Cause
Remedy
Suction weakens or
cleaner runs hot
Clogged filter
Brush dirt from filter. If condition continues,
change filter.
Air leak
Check all fittings for tight fit (nozzles, hose, etc.)
Check that tank cover is sealed properly.
Obstruction in hose
or nozzle
Check nozzle, hose, etc. for obstructions, and
remove if present.
Misting in the
exhaust air
Saturated filter
Replace saturated filter with a dry filter.
TROUBLESHOOTING
WARNING
– If ANy Of THE MOTOR HOUSING PARTS
SHOULD BECOME DETACHED OR BROkEN, EXPOSING THE MOTOR OR ANy
OTHER ELECTRICAL COMPONENTS, OPERATION SHOULD BE DISCONTINUED
IMMEDIATELy TO AVOID PERSONAL INjURy OR fURTHER DAMAGE TO THE
VACUUM. REPAIRS SHOULD BE MADE BEfORE REUSING THE VACUUM.
TWO yEAR HOME USE WARRANTy
your Shop-Vac
®
vacuum cleaner is warranted for normal household use, in accordance with
the user Manual, against original defects in material and workmanship for a period of two years
from date of purchase. Should this product be used for commercial or rental use, a 90 day lim-
ited warranty will apply. Shop-Vac Corporation warrants placing this vacuum cleaner in correct
operating condition, by repair or parts replacement, during the warranty period, without charge.
This warranty does not cover accessories. use of non-recommended filters and/or accessories
may void the manufacturer's warranty. Shop-Vac
®
assumes no responsibility for damage or
faulty performance caused by misuse, careless handling, and where repairs or modifications
have been made. do not attempt to service your vacuum beyond that described in the user
Manual. Proof of purchase date is required. The warranty gives you specific legal rights, and
you may have other rights which vary from state to state or province to province. This warranty
is void outside of the united States and Canada.
Customers in the united States: for product service contact Shop-Vac Corporation, Customer
Service, at (570) 326-3557 or go to www.shopvac.com/support. Visit www.shopvac.com for
your vacuum's parts list schematic.
Customers in Canada: for product service return the complete unit, (transportation pre-
paid), to the Authorized Shop-Vac
®
Service Center nearest you. Visit www.shopvac.ca for
a complete list of Authorized Service Centers in your area.
Customers in Mexico: for product service see paperwork that came with your unit.
STORAGE
Before storing your vacuum cleaner, the tank should be emptied
and cleaned. The power cord can be wrapped around the cord
wraps
(not standard with all models)
provided on the tank
cover
(figure 32)
or tool holder
(not standard with all models)
installed on tank cover
(figure 33)
on rear of unit.
If your unit
does not come with cord wraps or tool holder, the cord can be
wound around the tank cover
(figure 34)
.
Accessories may be stored in the tool
holder
(not standard on all models)
.
The vacuum should be stored indoors.
The vacuum is equipped with an automatic suction shut-off that operates when pick-
ing up liquids. As the level of the liquid rises in the tank, an internal float rises until it
seats itself against a seal at the intake of the motor, shutting off suction. When this
happens, the motor will develop a higher than normal pitch noise and the suction is
drastically reduced. If this occurs, turn unit off immediately. failure to turn unit off after
float rises and shuts off suction will result in extensive damage to the motor. To con-
tinue use, empty the liquid waste from the tank as outlined in the previous paragraph.
NOTE:
If ACCIdenTALLy TIPPed OVeR, The VACuuM COuLd LOSe SuCTIOn. If ThIS OCCuRS,
PLACe VAC In uPRIGhT POSITIOn And TuRn SWITCh Off. ThIS WILL ALLOW The fLOAT TO
ReTuRn TO ITS nORMAL POSITIOn, And yOu WILL Be ABLe TO COnTInue OPeRATIOn.
AUTOMATIC SUCTION SHUT-Off
LUBRICATION
no lubrication is necessary as the motor is equipped with lifetime lubricated bearings.
Without Tank Drain
Liquid waste may be emptied by removing the tank cover. To empty, stop the motor and remove
the plug from the wall receptacle. Remove the tank cover and deposit the liquid waste contents
in a suitable drain. After tank is empty, return the cover to its original position. To continue use,
plug the cord into the wall receptacle and turn the unit on.
With Tank Drain
Liquid waste may be emptied by removing the tank drain. To empty, turn unit off and remove
plug from wall receptacle. Remove the drain cap and deposit the liquid waste contents in a
suitable drain. After the tank is empty, return the drain cap to its original position. To continue
use, plug the cord into the wall receptacle and turn the unit on.
32
33
34
