background image

FILTER INSTALLATION AND MAINTENANCE (CONT’D.)

6.  

NOTE:

 When removing filter bag from tank, remove inlet deflector from filter bag collar and reinstall into  

deflector guide. Inlet deflector should always be in place for any type of cleaning. 

     WARNING 

  FOR FINE DUST AND POWDERS.

When vacuuming fine dust, or powders of any kind (plaster, drywall dust, cold ashes, concrete dust, etc.) 

a high efficiency drywall filter bag must be used. When vacuuming normal household dust and debris, 

standard household disposable filter bags may be used.

WET PICK UP OPERATION

1.  Your vacuum can be used for wet pick up. Remove ALL dirt and debris found in the tank. Remove all dry

  use filters, including the filter bag, from the vacuum.

2.  A clean cartridge filter may be used to pick up small quantities of liquid. To use the cartridge filter; follow

  the instructions under dry pick up.

3.  For vacuuming large quantities of liquid use a foam sleeve. If a foam sleeve did not come standard with

  your unit, one may be purchased at your local dealer, the Shop-Vac

®

 website or by contacting Shop-Vac

®

  customer service. To use the foam sleeve; follow the instructions in this section.

4.  Misting in the exhaust air or dripping of liquid around the tank cover may occur if the

  filter becomes saturated during wet pick up. If this occurs, remove the filter and allow

  to dry, or replace with another dry filter.

5.  Turn the unit off immediately upon completing a wet pick up job or when tank is full

  and ready to be emptied. When the tank is full, suction will drastically reduce. Refer

  to the automatic suction shut off section for more information. Raise the hose to drain

  any excess liquid into the tank. Follow the instructions in the emptying liquid waste 

section.

6.  Before storing the vacuum cleaner or using for dry pick up, clean and dry the interior of the tank and the

  underside of the tank cover. Clean and allow the filters to dry completely.

7.  Wet pick up accessories should be washed periodically; especially after picking up wet, sticky kitchen

  accidents. This can be accomplished with a warm solution of soap and water.
FOAM SLEEVE

1.  With the tank cover in an upside down position, slide the foam sleeve down over the 

lid cage, pulling until foam sleeve completely covers the lid cage.

2.  To clean the foam sleeve, side it up and off the lid cage. Shake excess debris off of the

  foam sleeve with a rapid up and down movement.

3.  Hold foam sleeve under running water for a couple minutes, rinsing from the inside of

  the filter. A water wash is not always required, depending on the condition of the filter.

4.  Check the filter for tears. If any are found, replace with a new filter.

BLOWER FEATURE

Your vacuum can be used as a powerful blower. To use the blower feature, clear the hose of any debris or

obstructions.

For vacuums with a blower port cover (not standard on all models),

 unscrew blower port cover located 

on the back of tank cover. The blower port cover is equipped with a retaining strap to prevent loss of the 

cover. 

NOTE:

 For maximum performance when vacuuming, remove the blower port cover.

Insert machine hose end into blower port located on the back of the tank cover.  

Twist the hose end slightly to tighten the connection. Caution should be used when using as a blower due to 

the powerful force of air when using certain attachments.

     WARNING 

 

ALWAYS WEAR EYE PROTECTION TO PREVENT ROCKS OR 

DEBRIS FROM BEING BLOWN OR RICOCHETING INTO THE EYES OR FACE WHICH CAN RESULT 

IN SERIOUS INJURY.

PAGE 12

Содержание 14RT Series

















































Отзывы: