background image

Page    of 9 

WORK AREA 

 

Keep work area clean, 

free of clutter, and well-lit.

 

Cluttered and dark work areas can cause 

accidents.

 

 

Keep children and bystanders 

away while operating a pallet truck. Distractions can cause you 

to lose control, so visitors should remain at a safe distance from the work area.

 

 

Be alert of your surroundings. 

Using a pallet truck in confined work areas may put you 

dangerously close to sharp tools and rotating parts.

 

PERSONAL SAFETY 

 

Stay alert, 

watch what you are doing, and use common sense when using a pallet truck. Do not 

use a pallet truck while you are tired or under the influence of drugs, alcohol, or medication. A 

moment of inattention while operating a pallet truck may result in serious personal injury. 

 

Dress properly. 

Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, 

clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught 

in moving parts. 

 

Use safety apparel and equipment. 

Use safety goggles or safety glasses with side shields that 

comply with current national standards or, when needed, a face shield. Use a dust mask if 

working in dusty work conditions. This applies to all persons in the work area. Also use non-skid, 

safety shoes, hard hats, gloves, dust collection systems, and hearing protection when 

appropriate. 

 

PALLET TRUCK USE AND CARE 

 

Do not modify the pallet truck

 

in any way.

 Unauthorized modification may impair the function 

and/or safety and could affect the life of the equipment. There are specific applications for which 

the pallet truck was designed. 

 

Always check for damaged or worn-out parts before using the pallet truck. 

Broken parts 

will affect the pallet truck operation. Replace or repair damaged or worn parts immediately.

 

 

Do not exceed the pallet truck

 

load capacity. 

 

Distribute the load evenly.

 Uneven loads may cause the pallet truck to tip, resulting in 

personal injury to the operator or others.

 

 

Use the pallet truck

 

on flat and level surfaces

 capable of supporting the pallet truck and its 

maximum load. Pulling or pushing a load on a slanted or uneven surface can result in loss of 

control.

 

 

Store idle pallet truck. 

When the pallet truck is not in use, store it in a secure place out of the 

reach of children. Inspect it for good working condition prior to storage and before re-use. 

 

 

 

 

 

Содержание DB-5500LB










Отзывы: