Shop fox W1701W Скачать руководство пользователя страница 23

Страница: 23 / 56

-21-

Model W1701W (For Machines Mfd. Since 1/16)

ATIO
NS

Stock.Inspection.&.

Requirements

Here.are.some.rules.to.follow.when.choosing.and.

shaping.stock:

•

DO.NOT.shape.stock.that.contains.large.or.loose.

knots.

Injury to the operator or damage to the

workpiece can occur if the knots become dislodged

during the cutting operation.

•

Avoid.shaping.against.the.grain.direction.

Cutting

against the grain increases the likelihood of stock

kickback, as well as tear-out on the workpiece.

•

Shaping.with.the.grain.produces.a.better.finish.

and.is.safer.for.the.operator.

Cutting with the grain

is described as feeding the stock so the grain points

down and toward you as viewed on the edge of the

stock.

•

Remove.foreign.objects.from.the.stock

Make sure

that any stock you process is clean and free of any

dirt, nails, staples, tiny rocks or any other foreign

objects that may damage the cutter, or create a

fire hazard if sparks are created. Wood stacked on a

concrete floor may contain small pieces of stone or

concrete and should be removed before shaping.

•

Make.sure.all.stock.is.sufficiently.dried.before.

shaping..

Wood with a moisture content over 20% will

cause unnecessary wear on cutter and produce poor

cutting results.

•

Avoid.stock.with.excessive.warping:.

Workpieces

with excessive cupping, bowing, or twisting are

dangerous to cut because they are unstable and

can move in unpredictable ways when being cut.

A workpiece supported on the bowed side will

rock during a cut and could cause kickback or

severe injury. DO NOT use workpieces with these

characteristics!

•

Choosing.your.material.type:

This machine is

intended for cutting natural and man-made wood

products, laminate covered wood products, and

some plastics. Cutting drywall or cementitious

backer board creates extremely fine dust and may

reduce the life of the bearings. This machine is

NOT designed to cut metal, glass, stone, tile, etc.;

cutting these materials with a table saw may lead to

injury.

Projectiles. thrown. from. the. machine.

could. cause. serious. eye. injury.. Wear.

safety.glasses.during.operation!

Turn. machine.

OFF

. and. allow. cutter.

to. come. to. a. complete. stop. before.

making. cutter. adjustments.. Failure.

to. follow. this. warning. could. result. in.

serious.personal.injury.

Содержание W1701W

























































Результаты поиска

Содержание W1701W

Отзывы:

Похожие инструкции для W1701W

Бренды по названию

Популярные бренды

Shop fox W1701W, Руководство пользователя

Результаты поиска

Содержание W1701W

Отзывы:

Похожие инструкции для W1701W

Бренды по названию

Популярные бренды