background image

Model W1793/W1794 Professional Spray Gun

-13-

Symptom

Possible

 

Cause

Possible Solution

Excessive over-
spray.

1. Fluid pressure too high.
2. Gun is too far from surface.

3. Spraying too fast.

1. Reduce fluid pressure.
2. Keep gun at recommended 

distance.

3. Slow down and maintain 

consistent, even parallel 
stroke.

Unable to control 
spray fan.

1. Pattern adjustment screw is 

not seating properly.

2. Atomizing cap is loose.

1. Clean or replace.

2. Tighten atomizing cap.

Runs and sags.

1. Damaged seal.

1. Replace damaged seals.

Material leaks from 
cup.

1. Cap not secure.
2. Cup not tight on gun body.
3. Leaking from cap vent hole.

1. Tighten.
2. Tighten.
3. Hold gun upright do not 

tilt.

Material leaks from 
gun.

1. Fluid tip loose.
2. Dry or damaged seals.
3. Excessive pressure.

1. Tighten.
2. Replace seals.
3. Reduce pressure.

Thick dimpled fin-
ish aka "Orange 
Peel."

1. Holding gun too close to sur-

face.

2. Inlet air pressure too low.
3. Material not properly mixed.

4. Surface is dirty or oily.

1. Spray at recommended dis-

tance.

2. Check inlet air pressure.
3. Follow manufacturer's 

instructions.

4. More surface prep is 

required.

Dry Spray.

1. Inlet air pressure too high.
2. Gun too far from surface.

3. Gun stroke too fast.

1. Lower inlet air pressure.
2. Keep gun at recommended 

distance.

3. Slow down and maintain 

consistent even parallel 
stroke.

Gun leaks from 
fluid tip.

1. Debris will not let the needle 

seat with the fluid tip.

1. Clean or replace both.

Contaminated 
paint.

1. Water or oil in the air line.

1. Install an in-line air filter.

2. Replace air line.

Содержание SHOP FOX W1793





















Отзывы: