Shinko Electric CHC-S1245-5 Скачать руководство пользователя страница 38

Страница: 38 / 49

YQE8-J0092E

Check

Item

Probable Cause

Corrective Action

Defective Ribbon Mark Sensor ASSY,

its connector, or cable disconnection.

Verify that the cable connection between Ribbon Sensor

ASSY and PCB HSSV7-JUNCTION-F ASSY (CN87-CN53,

CH88-CN53) is properly connected. If it is abnormal,

repairing at manufacturer is required.

Replace Ribbon Sensor ASSY 27 and if it works, the original

part is defective.

Defective PCB HSSV7-JUNCTION-F

ASSY, or cable disconnection.

Verify that cable connection between PCB HSSV7-CONT-F

ASSY and PCB HSSV7-JUNCTION-F ASSY (CN4-CN40)

is properly connected. If it is abnormal, repairing at

manufacturer is required.

Defective PCB HSSV7-CONT-F

ASSY.

Replace PCB HSSV7-CONT-F ASSY

１

and if it works,

the original part is defective.

Defective PCB HSSV7-JUNCTION-F

ASSY.

Replace PCB HSSV7-JUNCTION-F ASSY

３

and if it

works, the original part is defective.

Ribbon Mark Reflection Shield is dirty.

Verify that Ribbon Mark Reflection Shield Slicked on the

thermal head ASSY is not dirty. Clean if it is dirty

（

Refer to Section 2.6

）

Dust and/or foreign object in the ribbon

mark sensor ASSY.

Verify that there are no paper dusts, and foreign object on the

Ribbon Mark Sensor ASSY. (Refer to Section 2.6)

Defective DC Motor ASSY (Ribbon

Winding)

Use printer engine’s self diagnostic to test the operation of

DC Motor. If the diagnostic showed abnormality, replace the

DC Motor ASSY (Ribbon Winding)

６

Roll Failure of Ink Ribbon

Verify if there is no roll failure of Ink ribbon at winding or

supply side.

If there is roll failure, replace with the new ink ribbon.

Содержание CHC-S1245-5


















































Результаты поиска

Содержание CHC-S1245-5

Отзывы:

Похожие инструкции для CHC-S1245-5

Бренды по названию

Популярные бренды

Shinko Electric CHC-S1245-5, Инструкция по техническому обслуживанию

Результаты поиска

Содержание CHC-S1245-5

Отзывы:

Похожие инструкции для CHC-S1245-5

Бренды по названию

Популярные бренды