background image

 

OFS-80

 

Optical Fiber Fusion Splicer User’s Manual 

 

Shineway Technologies, Inc.                  

 

- 22 -

 

 

splice mode as shown above: 

 

Press 

  or

button  to  select  the  parameter  to  be  modified,  press 

 

  button  to 

enter parameter setting. 

Press 

  or

  button to modify parameter, press 

 

  button to confirm. 

 

In AUTO mode, certain parameters cannot be changed. 

Parameter 

Description 

Fiber Type 

List of splice modes stored in database is displayed. A selected splice   

mode stored in the database area is copied to a selected splice mode in   

the user-programmable area. 

Mode Title1 

Title for a splice mode expressed in up to seven characters. 

Mode Title2 

Detail explanation for a splice mode expressed in up to 15 characters.     

Title2 is displayed at the [Splice Mode Select] menu. 

Cleave Limit 

Set cleave limit. An error message is displayed if  the cleave angle of 

either the left or right fiber ends exceeds the selected threshold. 

Loss Limit 

An error message is displayed if the estimated splice loss exceeds   

selected threshold (loss limit). 

Arc Power 

In SM/DS/MM/NZ/AUTO modes, the Arc Power is fixed at 40 bits. 

Arc Time 

Arc Time is fixed at 1500 ms for SM and DS modes, 2000 ms for NZ   

mode, and 3000 ms for MM mode. This is automatically set depending 

on the fiber type when AUTO mode is selected. 

Cleaning Arc 

A cleaning arc burns out micro dust on the surface of the fiber with an   

arc discharge for a short period of time. The duration of the cleaning   

arc can be changed by this parameter. 

Rearc Time 

Splice loss may be improved by an additional “rearc” discharge in   

some cases. The duration of this additional arc can be changed by this 

parameter. 

 

4.1.2 Heater Mode 

There are 20 user-programmable heating modes. Select one best suitable for the protection 

sleeve used. 

 

Содержание OFS-80































Отзывы: