Shindaiwa T344 Скачать руководство пользователя страница 7

Страница: 7 / 28

NOTE:

The plastic shield is for use with the Nylon Line Head only. Install Metal

Shield when using plastic or metal blades.
1. Remove plastic threaded shaft sleeve and adapter plate (C) from PTO

shaft (A).

Place the shield on the bottom of the bearing housing flange.

3. Place shield plate (B) on shield, align holes. Install three (3) screws from

bottom through plate and shield into gear case.

Install trimmer head

IMPORTANT!

Semi-automatic nylon line heads must be used only with plastic debris shield

with cut-off knife. Using nylon line heads with metal debris shield can result

in trimmer damage, caused by operation with excessive line length.

To advance trimmer line

NOTE:

To advance trimmer line, tap trimmer head against the ground while the head
is turning at normal operating speed.

Nylon line replacement

See Maintenance Section for Loading Trimmer Line.

Remove nylon line head

NOTE:

Do not disassemble nylon line head.
1. Align locking hole in upper plate with notch in edge of gear housing and

insert head locking tool (D).

2. Remove line head (E) by turning it clockwise until head is completely off

of shaft.

3. Remove locking tool (D).

Cutting attachment shield

CAUTION

Wear Gloves or personal injury may result:

• Cutoff knife is sharp.

• Gearcase and surrounding area may be hot.

WARNING!

A standard grass trimmer with a loop handle should NEVER be operated with blade-type attachments. For

blade use, the trimmer must be fitted with a bicycle-type handlebar or a barrier bar that is located in front of the opera

tor to reduce the risk of the operator from coming in contact with the cutting attachment (per ANSI B175.3). When

using a blade, the unit must also be equipped with a harness or strap.

NOTE:

Use the 4 mm hexagonal wrench as a gear housing locking tool.
1. Assemble adapter plate (C) onto PTO shaft.
2. Align locking hole in upper plate with notch in edge of gear housing and

insert head locking tool (D).

3. Thread line head (E) onto shaft by turning it counter-clockwise until head

is tight against adapter plate (C).

4. Remove locking tool (D).

Содержание T344





























Результаты поиска

Содержание T344

Отзывы:

Похожие инструкции для T344

Бренды по названию

Популярные бренды

Shindaiwa T344, Руководство пользователя

Результаты поиска

Содержание T344

Отзывы:

Похожие инструкции для T344

Бренды по названию

Популярные бренды