Shindaiwa C262 Скачать руководство пользователя | Manualshive

Страница: 30 / 60

background image

OPERATION

C262

30

X7502341302

©

02/21

ECHO Incorporated

◆

WEAR SAFETY GLASSES when mixing or handling.

◆

AVOID repeated or prolonged skin contact.

◆

AVOID inhaling oil mists or vapors.

Shindaiwa branded 2-stroke oils may be mixed at 50:1 ratio for
application in all Shindaiwa engines sold in the past, regardless of
ratio specified in those manuals.

Handling Fuel

Fuel is VERY flammable. Use extreme care when mixing, storing
or handling, or serious personal injury may result.

◆

Use an approved fuel container.

◆

DO NOT smoke near fuel.

◆

DO NOT allow flames or sparks near fuel.

◆

Fuel tanks/cans may be under pressure. Always loosen
fuel caps slowly allowing pressure to equalize.

◆

NEVER refuel a unit when the engine is HOT or RUNNING!

◆

DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.

◆

DO NOT overfill fuel tank. Wipe up spills immediately.

◆

Securely tighten fuel tank cap and close fuel container
after refueling.

◆

Inspect for fuel leakage. If fuel leakage is found, do not
start or operate unit until leakage is repaired.

◆

Move at least 3 m (10 ft.) from refueling location before
starting the engine.

Gasoline vapor is heavier than air, and can travel along the
ground to nearby sources of ignition such as electrical motors,
pilot lights, and hot or running engines. Vapors ignited by an
ignition source can flash back to the fuel container, resulting in
an explosion, fire, serious or fatal injuries, and extensive
property damage.

«
...
28
29
30
31
32
...
»

Содержание C262





























































Отзывы:

Нет отзывов

Похожие инструкции для C262

Бренд: ZLINK Страницы: 2

Бренд: EarthQuake Страницы: 24

Бренд: Ryobi Страницы: 5

Бренд: BLACKLINE Страницы: 162

Бренд: AAVIX Страницы: 21

Бренд: Yard-Man Страницы: 56

Бренд: Gardenline Страницы: 16

Бренд: Gardenline Страницы: 24

Бренд: GreenWorks Pro Страницы: 44

Бренд: GE Страницы: 6

myTouchSmart MTS5406

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 16

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 22

INCREDI.PULL 316.79204.0

Бренд: Craftsman Страницы: 32

Incredi-Pull 316.791900

Бренд: Craftsman Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды