Shindaiwa AHS254 Скачать руководство пользователя страница 12

Страница: 12 / 32

Place the unit on a flat, level

surface.

2. Clear any dirt or other debris from

around the fuel filler cap.

Remove the fuel cap, and fill the

tank with clean, fresh fuel.

Reinstall the fuel filler cap and

tighten firmly.

5. Wipe away any spilled fuel before

starting engine.

CAUTION!

Slowly remove the fuel cap only

after stopping the engine

Filling the fuel tank

WARNING!

Minimize the Risk of Fire

■

NEVER

smoke or light fires near the

engine.

■

ALWAYS

stop the engine and allow

it to cool before refueling.

■

ALWAYS

Wipe all spilled fuel and

move at least 3 meters (10 feet) from

the fueling point and source before

starting.

■

NEVER

place flammable material

close to the engine muffler.

■

NEVER

operate the engine without

the muffler and spark arrester

screen in place and in good working

condition.

■

FUEL IS HIGHLY FLAMMABLE.

■

ALWAYS

store gasoline in a

container approved for flammable

liquids.

■

ALWAYS

inspect the unit for fuel

leaks before each use. During each

refill, check that no fuel leaks from

around the fuel cap and/or fuel

tank.

If fuel leaks are evident, stop using

the unit immediately. Fuel leaks

must be repaired before using the

unit.

■

ALWAYS

move the unit at least

3 meters (10 feet) away from a

fuel storage area or other readily

flammable materials before

starting

the engine.

After use

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage con

tainer.

Storage -

Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a

precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from

sparks and flames.

IMPORTANT!

Stored fuel may separate. ALWAYS shake fuel container thoroughly before each use.

Mixing Instructions

1. Fill an approved fuel container with half of the required amount of

gasoline.

2. Add the proper amount of engine oil to gasoline.

3. Close container and shake to mix oil with gasoline.

4. Add remaining gasoline, close fuel container, and remix.

IMPORTANT!

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may

require the use of automatic fuel shut-off

containers to reduce fuel spillage.

Содержание AHS254

































Результаты поиска

Содержание AHS254

Отзывы:

Похожие инструкции для AHS254

Бренды по названию

Популярные бренды

Shindaiwa AHS254, Руководство владельца/оператора

Результаты поиска

Содержание AHS254

Отзывы:

Похожие инструкции для AHS254

Бренды по названию

Популярные бренды