background image

Technical Service Instructions

SI-6C80D

ST-6510
ST-5500-CA
ST-5510
ST-R600

Shimano 

Total Integration

General Safety Information

WARNING

• Obtain, read and carefully service instructions when installing

parts. A loose, worn, or damaged parts may cause injury to
the rider.
We strongly recommend that only genuine Shimano
replacement parts be used.

• Read these Technical Service Instructions carefully, and keep

them in a safe place for later reference.

Note

• Operation of the levers related to gear shifting should be made

only when the front chainwheel is turning.

• For smooth operation, always be sure to use the specified

outer casing and the bottom bracket cable guide.

• Grease the inner cable and the inside of the outer casing

before use to ensure that they slide properly.

• Because the high cable resistance of a frame with internal

cable routing would impair the SIS function, this type of frame
should not be used.

• The end of the outer casing which has the aluminum 

cap should be at the derailleur side.

Derailleur side

4-mm cap

Plastic cap or 4-mm cap

Aluminum cap

• The cycle computers shown in the table below are compatible.

• Read the service instructions for the cycle computer also.
• Parts are not guaranteed against natural wear or deterioration

resulting from normal use.

• For maximum performance we highly recommend Shimano

lubricants and maintenance products.

• For any questions regarding methods of installation,

adjustment, maintenance or operation, please contact a
professional bicycle dealer.

SM-6500

*1

/ SM-6500-RS / SM-6501

SC-6500 / SC-6501 / SC-M500

Meter unit

Bracket sensor unit

*1

The bracket cover must be replaced.

(

)

ST-6510 ---> Replace with bracket cover for ST-6501.
ST-5500-CA ---> Replace with ST-5500-C.

27

FD-6503

FC-6503

RD-6500-GS

Series

Shifting lever

Outer casing

Gears

Front derailleur

Front chainwheel

Bottom bracket

Rear derailleur

Freehub

Cassette sprocket

Chain

ULTEGRA

ST-6510 / ST-R600

18

SP40

FH-6500

CS-6500

CN-HG93 / CN-7701

FD-6500

FC-6500

BB-6500

RD-6500

Bottom bracket cable guide

SM-SP17

In order to realize the best performance, we recommend that
the following combination be used.

27

FD-5503 / FD-5504

FC-5504 / FC-5505

RD-5500-GS /
RD-5501-GS

Series

Shifting lever

Outer casing

Gears

Front derailleur

Front chainwheel

Bottom bracket

Rear derailleur

Freehub

Cassette sprocket

Chain

SHIMANO 105

ST-5500-CA / ST-5510 / ST-R600

18

SP40

FH-5500 / FH-5501

CS-HG70-9

CN-HG73

FD-5500 / FD-5501

FC-5501 / FC-5502

BB-5500

RD-5500 /
RD-5501

Bottom bracket cable guide

SM-SP17

t

Содержание ST-5500-CA










Отзывы: