Shimaden PAC46 Series Скачать руководство пользователя страница 22

Страница: 22 / 24

13. External Equipment

13-1. External power adjuster (sold separately)

14. Inspection

14-1. Inspection and remedial measures when alarm is generated

Monitor lamp

Alarm Indication

Inspection and Remedial Measures

Red PL lights.

Open phase/phase
sequence abnormal/
frequency abnormal

Phase sequence of power supply is incorrect. Check wiring.

Operation is normal when green lamp is lit.

O.C. lights.

Over-current alarm
detected

Turn off power. Check and find cause of over-current and take appropriate measures. Then,
resupply power.

Over-current detection is not reset unless power supply to the instrument is turned off.

If over-current occurs, never resupply power without checking and taking remedial measures on
load side.

Otherwise, thyristor element may be destroyed.

FUSE lights.

Rapid fuse blown

Check load side, find cause of blown fuse, and take remedial measures. Then, replace it with new
rapid fuse. For the fuse replacement procedure, refer to 10-4 'Replacement of rapid fuse.'

H/B lights.

Heater break alarm

Check heater for heater break.

O.H. lights.

Internal temperature
abnormal

Check instrument body for overheating.

If current is 50 A or above, check fan for stoppage or slow rotation.

14-2. Troubleshooting

Symptom

Possible Cause

Remedy

Output is not produced.

Is voltage across power supply terminals (R, S, T)
normal?

Is alarm active? (Is Monitor lamp lit?)

Is control input signal normal?

Is internal power or external power setting normal?

Control board or thyristor element may have problem.

Output remains on.

Is control input signal normal?

Is internal power or external power setting normal?

Control board or thyristor element may have problem.

Alarm is output
frequently.

Is load short-circuited?

Check and repair load.

Has load insulation failed?

Check and repair load.

Is load capacity rating exceeded?

Replace the PAC46 with one having sufficient load
capacity.

Is phase sequence of power supply adjusted correctly?

Check power supply for phase sequence.

Output is out of
balance.

Is voltage across power supply terminals (R, S, T)
normal?

Is phase sequence of power supply correct?

Is one phase of load side broken?

Control board or thyristor element may have problem.

•

Model

•

Specifications

: QSV005/QSV006

: Characteristic/resistance: B/10 kΩ

: Lead: Vinyl lead 1 m included

Wire end treatment: Half-stripped

: Scale plate and knob, one each

䡡

Name and graduation

External power

(QSV005)

0 to 100%

Manual power

(QSV005)

0 to 100%

Base power

(QSV005)

0 to 100%

High-low power

(QSV005)

0 to 100%

Current limit setting
device

(QSV006)

50 to 100%

•

External dimensions and mounting dimensions

Содержание PAC46 Series

























Результаты поиска

Содержание PAC46 Series

Отзывы:

Похожие инструкции для PAC46 Series

Бренды по названию

Популярные бренды

Shimaden PAC46 Series, Инструкция по эксплуатации

Результаты поиска

Содержание PAC46 Series

Отзывы:

Похожие инструкции для PAC46 Series

Бренды по названию

Популярные бренды