Sherman + Reilly PLW-250-4-T Скачать руководство пользователя страница 27

Страница: 27 / 62

4.1

Section 4 • SERVICE

GENERAL SERVICE

Close attention to proper preventive measures

and service procedures will ensure and extend

trouble-free operation of equipment. Proper

lubrication and careful attention to the hydraulic

system suction filter are two vital areas. The ob-

jective of scheduled service should be to antici-

pate and prevent operational problems before

they require extended shutdown for repairs.

IMPORTANT INFORMATION

The service guidelines outlined in this manual

are effective methods. These guidelines are not

all inclusive. Anyone who performs service or

repair on a Sherman & Reilly machine must be

completely satisfied that no one’s safety will be

jeopardized and take responsibility for these

actions.

If there are any questions about safety, procedure

or precautions, contact

Sherman & Reilly

800-251-7780

before attempting to do the work.

Service should be scheduled to

allow adequate time so the

procedure can be completed

correctly. It must be done by

skilled, trained service person-

nel with a good basic knowl-

edge of equipment, proce-

dures, and safety practices.

Accurate records should be kept of all service

and repairs.

WARNING

Содержание PLW-250-4-T































































Результаты поиска

Содержание PLW-250-4-T

Отзывы:

Бренды по названию

Популярные бренды

Sherman + Reilly PLW-250-4-T, Операция, обслуживание и запчасти

Результаты поиска

Содержание PLW-250-4-T

Отзывы:

Бренды по названию

Популярные бренды