Shaw SDHmini Скачать руководство пользователя страница 32

11.2  Temperature

Typical ambient variations experienced throughout the world are quite 

acceptable but avoid placing the instrument in direct sunlight or near a source of 

radiant or convected heat. In countries that experience extremes of temperature, 

always carry out the automatic calibration with the instrument at its operating 

temperature.

11.3  Response Time

The response time of any water vapour pressure detector will naturally be very 

much quicker from dry to wet, than from wet to dry. This is the reason that the  

SDHmini is so successful. The sensor is kept in a dry condition when it is not in 

use and therefore results are obtained in the quickest possible time.
To check whether a particular instrument is within specification, carry out 

the automatic calibration procedure, close the instrument head and note the 

reading ten minutes later. If the unit has not dried down to -40 °C after this ten 

minute period, the instrument should be returned to your supplier/authorised 

distributor for examination.

11.4  Guarantee

All  products are guaranteed for two years from the date of purchase, some 

exclusions are as follows:
Removing protective guard from any sensor, subjecting sensor to shock or black 

list gases e.g. caustic and acidic gases like ammonia and chlorine, tampering with 

any internal electronics, subjecting to excessive flow rate, contaminants and 

general misuse.

If you suspect a fault which you feel needs to be attended to under guarantee 

please contact us for assistance hopefully to help fault find and effect a remedy 

and if this is not successful, to give precise instructions for the return for 

inspection.
No equipment will be replaced or repaired without having been returned for 

inspection either to ourselves or an authorised distributor.

11.5  Basic Definitions

Water Vapour Pressure

The pressure exerted by the water vapour contained in any mixture of gases. The 

total pressure exerted by the gas mixture is the sum of the pressures exerted by 

its components – including the water vapour. Water Vapour Pressure varies in 

direct proportion to the total gas.

32

Содержание SDHmini





































Отзывы: