Sharp XV-Z21000 Скачать руководство пользователя страница 48

Страница: 48 / 68

-46

■

The maintenance indicators (power, lamp and temperature warning indicators) on the projector will let

you be aware of problems inside the projector. If any of the indicators illuminates, follow the relevant

procedures given below.

About the temperature warning indicator

If the temperature inside the
projector increases, due to
blockage of the exhaust or
intake vent, or the setting loca-
tion, “

” will blink in the lower left corner of

the picture. If the temperature keeps on rising,
the lamp will turn off and the temperature warning
indicator will blink, the cooling fan will run, then
the projector will enter the standby mode. After
“

” appears, be sure to perform the measures

described on the table below.

About the lamp indicator

■

When the remaining lamp

life becomes 5% or less,

(yellow) and “Change

The Lamp” will be dis-
played on the screen. When the percentage
becomes 0%, it will change to

(red), the lamp

will automatically turn off and then the projector
will automatically enter standby mode. At this
time, the lamp indicator will illuminate in red.

■

If you try to turn on the projector a fourth time

without replacing the lamp, the projector will

not turn on.

Maintenance indicator

Condition

Problem

Possible Solution

Temperature

warning

indicator

Normal

Abnormal

Off

Red on
(Standby)

The internal
temperature is
abnormally high.

Abnormal

•

Blocked exhaust or

intake vent

•

Relocate the projector to an area

with proper ventilation.

•

Cooling fan break-

down

•

Internal circuit failure

•

Clogged exhaust or

intake vent

•

Take the projector to your nearest

Sharp Authorized Service Center or
Dealer for repair.

•

Clean the exhaust and intake vents

according to the procedure on page

Lamp

indicator

Red on
(Standby)

The lamp does
not illuminate.

•

Burnt-out lamp

•

Lamp circuit failure

•

Replace the lamp. (See page

Take the projector to your nearest
Sharp Authorized Service Center or
Dealer for repair.

•

Please exercise care when replac-

ing the lamp.

•

Securely install the lamp unit cover.

Blue on*

Blue

blinks

when the

lamp is

active.

Power

indicator

The power
indicator blinks
in red when the
projector is on.

•

The lamp unit cover

is open.

•

Securely install the lamp unit cover.

•

If the power indicator blinks

even when the lamp unit cover is
securely installed, contact your
nearest Sharp Authorized Service
Center or Dealer for advice.

Blue on*/
Red on

Red blinks

Lamp replace-
ment time.

•

The remaining lamp

life has become 5%
or less.

* Blue is off when “LED” is set to “Off”. (See page

Maintenance Indicators/Maintenance

Lamp indicator

Power indicator

Temperature warning indicator

XVZ21000̲E̲Ousyu̲P46-51.indd 46

2006/07/31 19:55:51

Содержание XV-Z21000





































































Результаты поиска

Содержание XV-Z21000

Отзывы:

Похожие инструкции для XV-Z21000

Бренды по названию

Популярные бренды

Sharp XV-Z21000, Руководство по эксплуатации

Результаты поиска

Содержание XV-Z21000

Отзывы:

Похожие инструкции для XV-Z21000

Бренды по названию

Популярные бренды