Sharp XL-DV100NH, Руководство по эксплуатации

Страница: 45 / 48

XL-DV100NH_001 EN.fm
E-34
2009December 14
8
7
6
5
4
3
2
1
Timer and sleep operation (Remote
control only) (continued)
The radio, compact disc and USB can all be turned off
automatically.
To confirm the remaining sleep time:
To cancel the sleep operation:
Press the ON/STAND-BY button whilst “SLEEP” is
indicated. To cancel the sleep operation without setting the
unit to the stand-by mode, proceed as follows.
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
Enhancing your system
Enhancing your system (continued)
Note:
To prevent noise interference, place the unit away from the
television.
●
Before plugging in or unplugging the headphones,
reduce the volume.
●
Be sure your headphones have a 3.5 mm (1/8")
diameter plug and impedance between 16 and 50
ohms. The recommended impedance is 32 ohms.
●
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME
control.
Troubleshooting chart
Many potential problems can be resolved by the owner
without calling a service technician.
If something is wrong with this product, check the following
before calling your authorised SHARP dealer or service
centre.
■
Sleep operation
1
Play back the desired sound source.
2
Press the SLEEP button.
3
Within 10 seconds, press the SLEEP button repeatedly
to select the time.
10 20 30 ... 80 90
4
“SLEEP” will appear.
5
The unit will enter the power stand-by mode
automatically after the preset time has elapsed.
1
Whilst “SLEEP” is indicated, press the SLEEP button.
The remaining time is displayed for about 10 seconds.
1
Whilst “SLEEP” is indicated, press the SLEEP button.
2
Within 10 seconds, press the SLEEP button repeatedly
to select “SLEEP 00”.
■
To use timer and sleep operation together
1
Set the sleep time (see above, steps 1 - 5).
2
Whilst the sleep timer is set, set the timer playback
(steps 2 - 10, page 33).
■
Listening to the playback sounds of
portable audio player, etc.
1
Use a connection lead to connect the portable audio
player etc. to the AUX IN socket. When using video
equipment, connect the audio output to this unit and the
video output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the AUX button on the remote control or
FUNCTION button repeatedly on main unit to select
AUX IN function.
Desired time
10 - 90 minutes
Sleep operation will
automatically stop
Sleep timer setting Timer playback setting
End time
Timer playback
start time
4
Play the connected equipment. If volume level of the
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase
the volume of the connected device.
■
Headphones
■
General
Symptom Possible cause
●
The clock is
not set to the
correct time.
●
Did a power failure occur? Reset
the clock.
●
When a
button is
pressed, the
unit does not
respond.
●
Set the unit to the power stand-by
mode and then turn it back on.
●
If the unit still malfunctions, reset it.
●
No sound is
heard.
●
Is the volume level set to “MIN”?
●
Are the headphones connected?
●
Are the speaker wires
disconnected?
■
CD player
Symptom Possible cause
●
Playback
does not start.
●
Is the disc loaded upside down?
●
Does the disc satisfy the
standards?
●
Is the disc distorted or scratched?
●
Playback
stops in the
middle or is
not performed
properly.
●
Playback
sounds are
skipped, or
stopped in the
middle of a
track.
●
Is the unit located near excessive
vibrations?
●
Is the disc very dirty?
●
Has condensation formed inside
the unit?