Sharp XE-A506 Скачать руководство пользователя

Страница: 72 / 132

If an error occurs while data is transferred from your cash register to the inserted SD memory card and vice
versa, it will be indicated by a corresponding error message shown on the operator display. Press the

key to

clear the error, then take the corresponding action.

SD error message table

In Case of SD Error

Display

Error status and action

(Error message)

NO CARD

No SD memory card is found. Insert an SD memory card into the SD card slot or reinsert it correctly.

CARD PROTECT

The write-protect switch on the SD memory card is in the “PROTECTED” position. Set the switch on

the “NOT PROTECTED” position.

CARD FULL

The SD memory card is full. Delete unwanted data from the card on a PC or replace the card with a

new one. When using a new SD memory card, be sure to format it in advance.

ACCESS ERROR

The SD memory card has no desired data. Replace it with another SD memory card containing the

desired data.

FILE FAILED

The data stored in the SD memory card is incorrect. Write correct data into the SD memory card on a

PC.

OVER LIMIT.

The maximum allowable number of times of sales data is exceeded. Delete unwanted data from the

SD memory card on a PC or replace the card with a new one. When using a new SD memory card, be

sure to format it in advance.

POWER OFF

A power failure has occurred while the SD memory card is accessed. Perform the interrupted

operation again from the beginning after power recovery.

SD CANCEL

The data transfer operation has been canceled. Perform the same operation again from the beginning.

SD ERROR

An error other than the above mentioned has occurred while the SD memory card is accessed.

Perform the interrupted operation again from the beginning.

A506_5 FOR THE MANAGER_SD 09.10.14 9:27 AM Page 70

Содержание XE-A506





































































































































Результаты поиска

Содержание XE-A506

Отзывы:

Похожие инструкции для XE-A506

Бренды по названию

Популярные бренды

Sharp XE-A506, Инструкция по эксплуатации

Результаты поиска

Содержание XE-A506

Отзывы:

Похожие инструкции для XE-A506

Бренды по названию

Популярные бренды