Sharp VC-A136X Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 25

Sharp VC-A136X Скачать руководство пользователя страница 7

Disconnecting TV Cable

Disconnect the aerial cable from the back of

your TV set.

Connecting Aerial Cable to VCR

Connect the aerial cable to the

ANTENNA

terminal of your VCR.

Connecting VCR to TV

Connect the supplied coaxial cable to the

RF

OUT

terminal of the VCR. Plug the other end

into your TV’s ANTENNA IN terminal.

RF OUT

I

ANTENNA IN

TV

back panel

IN

I

N

To view the output of your VCR on the television screen, you must select an unused channel on your TV
and tune it to the output of your VCR (factory preset to UHF channel 37). Refer to the TV operation
manual.

NOTE:

l

TUNE THE TV. NOT THE VCR.

Select an unused channel on your TV and press the

OPERATE

button on the VCR to turn on the power.

Set the TEST SIG

switch to ON.

Adjust the tuning of the selected TV channel until the test pattern (two vertical bars) appears on the
screen. This channel becomes the “VIDEO CHANNEL”.

Set the

TEST SIG

switch to

OFF.

NOTE:

l

If interference or a beat pattern is received when the test pattern is tuned in, use a small screwdriver to turn the

RF

converter output

channel adjuster to change the VCR output channel, and then retune your

TV

as above.

6

OPERATE

RF converter out

«
...
5
6
7
8
9
...
»

Содержание VC-A136X


























Отзывы:

Нет отзывов