Sharp UX-B700 Скачать руководство пользователя

Страница: 99 / 114

9. T

roub

le-

shooting

9. Troubleshooting

Problems and Solutions

Line error

Problem

Solution

LINE ERROR appears in
the display.

A line error occurs when your fax machine cannot
communicate correctly with the other fax machine.
The error is usually due to a problem on the phone
line.

Try the transaction again. If the error persists, check
the following:

• Check the connection. The cord from the

TEL.

LINE

socket to the wall socket should be no longer

than two meters.

• Make sure there are no modem devices sharing the

same telephone line.

• Check with the other party to make sure their fax

machine is functioning properly.

• Have your telephone line checked for line noise.

• Try connecting the fax machine to a different

telephone line.

• If the problem still occurs, your fax machine may

need service.

all.book Page 97 Friday, April 1, 2005 9:53 AM

Содержание UX-B700



















































































































Результаты поиска

Содержание UX-B700

Отзывы:

Похожие инструкции для UX-B700

Бренды по названию

Популярные бренды

Sharp UX-B700, Руководство по эксплуатации

Результаты поиска

Содержание UX-B700

Отзывы:

Похожие инструкции для UX-B700

Бренды по названию

Популярные бренды