background image

5

AFTER INSTALLATION

1. Remove all the stickers and items from the top of the cooktop 

surface.

2. Clean cooktop before use. Dry with a soft cloth. See “Cleaning 

Your Cooktop” in the operation manual for reference.

3. Read “Using the Cooktop” in the operation manual.
4. Turn on the power to the cooktop.
5. Verify all functions operate properly.

NOTE: If the cooktop does not work, or you find any problem 

in your operation, please check that the circuit breaker has not 

tripped, or a fuse has not blown. For more information, please 

See Troubleshooting Guide in the operation manual. If you do 

not solve the problem by yourself, please contact us for assistance 

or service

FCC STATEMENT

This device complies with Part 18 of the FCC Rules. NOTE:
This equipment has been tested and found to comply with the 

limits for a Consumer ISM equipment, pursuant to Part 18 of 

the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance 

with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference 

will not occur in a particular installation.
Please note that changes or modifications of this product is not 

expressly approved by the party responsible for compliance could 

void the user's authority to operate the equipment.
If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Содержание SDH3042DB









Отзывы: