Sharp R-351NW Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

background image

R-351NW

[6] POSITIVE LOCK CONNECTOR (NO-CASE TYPE) REMOVAL

[8] GRAPHIC SHEET AND MEMBRANE SWITCH REPLACEMENT

1. REMOVAL

1. CARRY OUT 3D CHECKS.
2. Remove the control panel assembly, referring to chapter of

CONTROL PANEL ASSEMBLY REMOVAL.

3. Remove the three (3) screws holding the control unit to the

control panel frame. And remove the control unit.

4. Remove the LCD holder and the rubber connector from the

control panel frame.

5. Tear away the graphic sheet from the control panel frame.
6. Tear away the membrane switch from the control panel

frame.

2. REINSTALLATION

1. Remove remaining adhesive on the control panel frame

surfaces with a soft cloth soaked in alcohol.

2. Tear the backing paper from the new membrane switch.
3. Insert the ribbon cable of the membrane switch into the slit

of the control panel frame.

4. Adjust the upper edge and right edge of the membrane

switch to the small depression on the surface of the control
panel frame.

5. Attach the membrane switch to the control panel frame by

rubbing with a soft cloth not to scratch.

6. Tear the backing paper from the new graphic sheet.

11 - 3

2. REINSTALLATION

1. Reinstall the magnetron to waveguide

fl

ange with the

four (4) screws.

2. Reinstall the air duct to the oven cavity top plate and

the magnetron with two (2) screws.

3. Insert the end of the chassis support into the hole of

the oven cavity front

fl

ange.

4. Hold the other end of the chassis support to the

magnetron with the one (1) screw.

5. Reconnect the wire leads to the magnetron. Refer to

“PICTORIAL DIAGRAM”.

6. Reinstall outer case and check that the oven is

operating properly.

CAUTION: WHEN REPLACING MAGNETRON, BE

SURE THE R.F. GASKET IS IN PLACE AND

MOUNTING SCREWS ARE TIGHTENED

SECURELY.

[7] CONTROL PANEL ASSEMBLY REMOVAL

1.   Disconnect the power supply cord and remove outer case.
2.   Open the door and block it open.
3.   Discharge high voltage capacitor.
4.   Disconnect the leads from the control unit.

1.   Disconnect the power supply cord, and remove outer case.
2.   Open the door and block it open.
3.   Discharge high voltage capacitor.
4.   Push the lever of positive lock

®

connector.

5. Pull down on the positive lock

®

connector.

CAUTION: WHEN CONNECTING THE POSITIVE LOCK

®

CONNECTORS TO THE TERMINALS, CONNECT

THE POSITIVE LOCK

®

SO THAT THE

LEVER

FACES

YOU

Terminal

Push

Pull down

1

2

Lever

Positive lock¨

connector

Figure C-1. Positive lock

®

connector

5. Remove the one (1) screw holding the control panel

assembly to the oven

fl

ange.

6. Slide the control panel assembly upward and remove it.
7. Now, individual components can be removed.

7. Adjust the upper edge and left edge of the graphic sheet

to the large depression on the surface of the control panel
frame.

8. Attach the graphic sheet to the control panel frame by

rubbing with a soft cloth not to scratch.

9. Make sure that the liquid crystal display and the LED sheet

are installed in position.

10. Tear the small backing paper from the ribbon cable of the

membrane switch.

11. Attach the ribbon cable to the control panel frame rear side.
12. Place the edge of the membrane switch’s ribbon cable on

the lower portion of the liquid crystal display.

13. Insert the rubber connector into the long slit of the LCD

holder.

14. Reinstall the control unit to the control panel frame with the

three (3) screws.

NOTE:

Do not contact the contact surface of the ribbon

cable (edge) and the rubber connector directly with

your

fi

ngers.

This is to avoid oxidized. If display digits are

missing or scrambled, remove control unit

and clean contact surface with alcohol.

Service_R-351NW.indd 26

Service_R-351NW.indd 26

6/26/09 6:30:55 PM

6/26/09 6:30:55 PM

«
...
24
25
26
27
28
...
»

Содержание R-351NW









































Отзывы:

Нет отзывов

Похожие инструкции для R-351NW

Бренд: Candy Страницы: 160

Бренд: Candy Страницы: 103

GLOMJB19S2SWZ-10

Бренд: Galanz Страницы: 24

Бренд: Midea Страницы: 21

Modernist Microwave In-A-Drawer DMR30M977WS

Бренд: Dacor Страницы: 15

Бренд: Blomberg Страницы: 96

Microvent PLCEM044K10

Бренд: Porter & Charles Страницы: 5

Бренд: West Bend Страницы: 20

Бренд: MBM Страницы: 81

Бренд: Magic Chef Страницы: 23

Бренд: Sammic Страницы: 64

Бренд: Omega Страницы: 18

Бренд: Jenn-Air Страницы: 40

Бренд: Falcon Страницы: 9

Бренд: Daewoo Страницы: 30

Бренд: Pelgrim Страницы: 68

Бренд: GEAppliances Страницы: 24

italia 94 professionale

Бренд: Drija Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды