Sharp R-305HK Скачать руководство пользователя страница 25

Страница: 25 / 36

R-305HK
R-305HW

Removal
1. Disconnect the power supply cord and then remove

outer case.

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect all wire leads from magnetron.
5. Remove the one (1) screw holding the chassis support

to the magnetron.

6. Release the chassis support from the hole of the oven

cavity front flange.

7. Remove the two (2) screws holding air duct to magnetron

and oven cavity top plate.

8. Remove the air duct from oven.
9. Carefully remove the four (4) screws holding magnetron

to waveguide flange.

10.Remove magnetron with care so that magnetron antenna

is not hit by any metal object around antenna.

11.Now, the magnetron is free.
Reinstallation
1. Reinstall the magnetron to waveguide flange with the

four (4) screws.

2. Reinstall the air duct to the oven cavity top plate and the

magnetron with two (2) screws.

3. Insert the end of the chassis support into the hole of the

oven cavity front flange.

4. Hold the other end of the chassis support to the magnetron

with the one (1) screw.

5. Reconnect the wire leads to the magnetron. Refer to

"PICTORIAL DIAGRAM".

6. Reinstall outer case and check that the oven is operating

properly.

CAUTION: WHEN REPLACING MAGNETRON, BE SURE

THE R.F. GASKET IS IN PLACE AND MOUNT-
ING SCREWS ARE TIGHTENED SECURELY.

MAGNETRON REMOVAL

HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL

1. Disconnect the power supply cord and then remove

outer case.

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the high voltage wire of the power transformer

from the high voltage capacitor.

5. Disconnect the high voltage wire of high voltage rectifier

assembly from the magnetron.

6. Disconnect the filament lead (short one) of the power

transformer from the high voltage capacitor.

7. Remove the one (1) screw holding capacitor holder to

bottom plate.

8. Remove one (1) screw holding high voltage rectifier

assembly to capacitor holder.

9. Disconnect rectifier terminal from capacitor.

High voltage rectifier assembly is now free.

10.Remove capacitor holder. Capacitor is now free.

CAUTION: WHEN REPLACING HIGH VOLTAGE RECTI-

FIER AND HIGH VOLTAGE CAPACITOR,
GROUND SIDE TERMINAL OF THE HIGH
VOLTAGE RECTIFIER MUST BE SECURED
FIRMLY WITH A GROUNDING SCREW.

CAUTION: 1. DISCONNECT OVEN FROM POWER SUP

PLY BEFORE REMOVING OUTER CASE.

2. DISCHARGE THE HIGH VOLTAGE CA-

PACITOR BEFORE TOUCHING ANY OVEN
COMPONENTS OR WIRING.

NOTE: When replacing the outer case, the 2 special

Torx screws must be reinstalled in the same
locations.

1. Disconnect the power supply cord and then remove

outer case.

2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads (primary) from power transformer

and the filament leads and high voltage wire from the
magnetron and capacitor terminals.

5. Remove four (4) screws (two (2) screws from the upper

side and two (2) screws from bottom side) holding
transformer to bottom plate.

6. Remove transformer from bottom plate.

POWER TRANSFORMER REMOVAL

Reinstallation
1. Rest transformer on the bottom plate with its primary

terminals toward the oven face plate.

2. Secure transformer with four (4) screws (two (2) screws

from the upper side and two (2) screws from bottom side)
to bottom plate.

3. Reconnect wire leads (primary) to power transformer

and filament leads and high voltage wire of transformer
to magnetron and high voltage capacitor. Refer to
"PICTORIAL DIAGRAM" on page 28.

4. Reinstall outer case and check that oven is operating

properly.

Special screw

Screw Driver
(Type: TORX T20 H or
GTXH20-100)

Содержание R-305HK





































Результаты поиска

Содержание R-305HK

Отзывы:

Похожие инструкции для R-305HK

Бренды по названию

Популярные бренды

Sharp R-305HK, Руководство по обслуживанию

Результаты поиска

Содержание R-305HK

Отзывы:

Похожие инструкции для R-305HK

Бренды по названию

Популярные бренды