Sharp R-305HK Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 36

background image

24

R - 305HK
R-305HW

1. Disconnect the power supply cord, and then remove

outer case.

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock

®

connector.

5. Pull down on the positive lock

®

connector.

CAUTION: WHEN CONNECTING THE POSITIVE LOCK

®

CONNECTORS TO THE TERMINALS, CON-
NECT THE POSITIVE LOCK

®

SO THAT THE

LEVER FACES YOU

POSITIVE LOCK

®

CONNECTOR (NO-CASE TYPE) REMOVAL

Terminal

Push

Pull down

1

2

Lever

Positive lock®

connector

Figure C-1. Positive lock

®

connector

1. Disconnect the power supply cord and then remove

outer case.

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from control unit.

CONTROL PANEL ASSEMBLY REMOVAL

5. Remove the one (1) screw holding the control panel

assembly to the oven flange.

6. Slide the control panel assembly upward and remove it.
7. Now, individual components can be removed.

Removal
1. Disconnect the power supply cord and then remove

outer case.

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the control panel assembly, referring to chapter

of CONTROL PANEL ASSEMBLY REMOVAL.

5. Tear away the graphic sheet from the control panel

frame and control unit assembly

6. Remove the two (2) screws holding the control unit

assembly to the control panel frame.

7. Release the ontrol unit assembly from the six (6) tabs of

the control panel frame.

8. Now, the ontrol unit assembly is free.

Installation
1. Remove remaining adhesive on the control panel frame

surfaces with a soft cloth soaked in alcohol.

2. Make sure that the LED sheet and liquid crystal display

are installed in position.

3. Reinstall the control unit assembly to the control panel

frame with the two (2) screws.

4. Tear the backing paper from the graphic sheet.
5. Adjust the upper edge and left edge of the graphic sheet

to the large depression on the surface of the control
panel frame.

6. Attach the graphic sheet to the control panel frame by

rubbing with a soft cloth not to scratch.

NOTE:
Do not contact the contact surface of the ribbon cable
(edge) and the rubber connector directly with your
fingers. This is to avoid oxidized. If display digits are
missing or scrambled, remove control unit and clean

CONTROL UNIT ASSEMBLY REPLACEMENT

Figure C-2. Graphic Sheet Attachment

Graphic sheet

Liquid
crystal display

Control panel
frame

LED sheet

Rubber connector

Contact surface

Ribbon cable
of membrane
switch

Control panel frame
(Rear side)

contact surface with alcohol. After cleaning, do not
attach the rubber connector until alcohol dries up. Do
not use alcohol or solution to clean the rubber connec-
tor. Make sure that there is no trash or foreign sub-
stance on contact surface of the rubber connector.

«
...
24
25
26
27
28
...
»

Содержание R-305HK





































Отзывы:

Нет отзывов

Похожие инструкции для R-305HK

Бренд: NEC Страницы: 22

Бренд: PALSON Страницы: 29

Бренд: Lakeland Страницы: 25

Profile Advantium PSB9240DFBB

Бренд: GE Страницы: 76

Бренд: Candy Страницы: 160

Бренд: Candy Страницы: 103

Бренд: Blodgett Страницы: 50

Бренд: Smeg Страницы: 27

B87VS38 0B Series

Бренд: NEFF Страницы: 60

Бренд: NEFF Страницы: 72

Бренд: Stilevs Страницы: 24

Бренд: Lang Страницы: 28

Бренд: Galanz Страницы: 14

Бренд: Daewoo Страницы: 17

Бренд: Omega Страницы: 20

Бренд: Belling Страницы: 24

NR4GR31 1 Series

Бренд: NEFF Страницы: 36

SpacemakerXL JVM1542BF

Бренд: GE Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды