background image

MX-3114N  MX-2314N/2614N/3114N (MAIN UNIT)  2 – 4

When  installing  the  machine,  there  is  no  need  to  remove  or
install the OPC drum unit. If it must be removed or installed for
any  reason,  follow  the  procedures  below.  When  removing  or
installing the OPC drum unit, put your hand from below the unit
and slide it in parallel along the guide on the right side. 
At that time, be careful not to touch the OPC drum surface.

10) Close the drum positioning cover, and lock it.

11) Re-install the waste toner box and lock into place.

B. Set the control level for the reference toner 

density

Setting  of  the  reference  toner  density  control  level  must  be  per-
formed with the toner cartridge removed.

If setting is performed with the toner cartridge installed, the EE-EL
error or an overtoner trouble may occur.

1)

With  the  front  cabinet  open,  connect  the  power  plug  to  the
power outlet.

2)

Turn ON the main power switch of the machine and the power
switch on the operation panel.

3)

Enter the SIM25-2 mode.

4)

After entering the simulation, close the front cabinet.

5)

Select K, C, M, Y and then press the [EXECUTE] button. The
system then performs  the  simulation, samples  the  toner den-
sity  control  sensor  value,  and  sets  (stores  in  memory)  the
average sensor detection level as the control level for the ref-
erence toner density. (Operating times: approx. 1.5 minutes)

Be sure to select all of the four colors: K, C, M, Y.

6)

After the machine completes cycling, exit the simulation mode.

7)

Confirm  that  “Install  the  toner  cartridge”  is  displayed,  and
install the toner cartridge by the following procedures.

8)

Shake the toner cartridge horizontally several times.

2

1

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

Содержание MX-2314N




















Отзывы: