Sharp LS013B7DH07 Скачать руководство пользователя страница 8

Страница: 8 / 34

SPEC No.

LD-28204A

MODEL No.

LS013B7DH07

PAGE

(7) A still image should be displayed less than two hours, if it is necessary to display still image

longer than two days, display image data must be refreshed

in order to avoid sticking image on LCD panel.

(8) If LCD module takes a static electricity, as the display image which is written into pixel memory might

not be displayed, Data update should be executed frequently.

(9) It is neither a breakdown nor a defective indication though very slight change in black level might be

periodically seen in a black part on the black display image according to the source of light (angle of the

luminance and the source of

light).

(10) Be sure to follow the absolute maximum rating in the specification. The design should consider the

surrounding temperature, the fluctuating input signal, and tolerance of the electronic parts. Exceeding

values is possible to cause worse characteristic such as burn and/or broken of the parts on LCD module.

(11) Follow the power, signal, and supply voltage sequence which the specification indicates, regarding on-off

input signal after power on of LCD module.

(12) According to the using application, power circuit protection is recommended at module failure.

(13) Nature of dew consideration prevention is necessary when LCD is used for long time under

high-temperature and high-humidity

SHARP Confidential

technical

literature

Содержание LS013B7DH07


































Результаты поиска

Содержание LS013B7DH07

Отзывы:

Бренды по названию

Популярные бренды

Sharp LS013B7DH07, Техническая литература

Результаты поиска

Содержание LS013B7DH07

Отзывы:

Бренды по названию

Популярные бренды