Sharp LS013B7DH07 Скачать руководство пользователя страница 3

Страница: 3 / 34

SPEC No.

LD-28204A

MODEL No.

LS013B7DH07

PAGE

NOTICE

Precautions>>

Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or

by any means, electronic or mechanical for any purpose, in whole or in part, without the express

written permission of SHARP. Express written permission is also required before any use of

this publication may be made by a third party.

b) The application circuit examples in this publication are provided to explain the representative applications of

SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right

or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial

property right or a third party resulting from the use of SHARP's devices, except for those resulting directly

from device manufacturing processes.

c) When using the products covered herein, please observe the conditions and the precautions written herein.

In no event shall the company be liable for any damages resulting from failure to strictly adhere to these

conditions and precautions.

d) SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures

and other contents described herein at any time without notice in order to improve design or reliability. Contact

SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing

locations are also subject to change without notice.

e) The devices in this publication are designed for general electronic equipment use.

f) The appropriate design measures should be taken to ensure reliability and safety when

SHARP's devices are used for equipment such as:

・

Transportation control and safety equipment(i.e.,aircraft, trains, automobiles, etc.)

・

Traffic signals

・

Gas leakage sensor breakers

・

Alarm equipment

・

Various safety devices etc.

g) SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as:

・

Aerospace equipment

・

Military and space applications

・

Nuclear power control equipment

・

Medical equipment for life support

・

Trunk line commucation equipment

SHARP Confidential

technical

literature

Содержание LS013B7DH07


































Результаты поиска

Содержание LS013B7DH07

Отзывы:

Бренды по названию

Популярные бренды

Sharp LS013B7DH07, Техническая литература

Результаты поиска

Содержание LS013B7DH07

Отзывы:

Бренды по названию

Популярные бренды